* ONEWAY:: One way analysis of variance.
* RANK:: Compute rank scores.
* REGRESSION:: Linear regression.
+* RELIABILITY:: Reliability analysis.
@end menu
@node DESCRIPTIVES
/PLOT=@{BOXPLOT, NPPLOT, HISTOGRAM, ALL, NONE@}
/CINTERVAL n
/COMPARE=@{GROUPS,VARIABLES@}
- /ID=@{case_number, var_name@}
+ /ID=var_name
/@{TOTAL,NOTOTAL@}
/PERCENTILE=[value_list]=@{HAVERAGE, WAVERAGE, ROUND, AEMPIRICAL, EMPIRICAL @}
/MISSING=@{LISTWISE, PAIRWISE@} [@{EXCLUDE, INCLUDE@}]
each containing one boxplot per dependent variable.
If the /COMPARE subcommand is ommitted, then PSPP uses the default value of
/COMPARE=GROUPS.
+
+The ID subcommand also pertains to boxplots. If given, it must
+specify a variable name. Outliers and extreme cases plotted in
+boxplots will be labelled with the case from that variable. Numeric or
+string variables are permissible. If the ID subcommand is not given,
+then the casenumber will be used for labelling.
The CINTERVAL subcommand specifies the confidence interval to use in
calculation of the descriptives command. The default it 95%.
[ /STATISTICS=@{DESCRIPTIVES@} ]
[ /MISSING=@{ANALYSIS, LISTWISE@} @{INCLUDE, EXCLUDE@} ]
+
+ [ /METHOD=EXACT [ TIMER [(n)] ] ]
@end display
NPAR TESTS performs nonparametric tests.
If the /STATISTICS subcommand is also specified, then summary statistics are
produces for each variable that is the subject of any test.
+Certain tests may take a long time to execute, if an exact figure is required.
+Therefore, by default asymptotic approximations are used unless the
+subcommand /METHOD=EXACT is specified.
+Exact tests give more accurate results, but may take an unacceptably long
+time to perform. If the TIMER keyword is used, it sets a maximum time,
+after which the test will be abandoned, and a warning message printed.
+The time, in minutes, should be specified in parentheses after the TIMER keyword.
+If the TIMER keyword is given without this figure, then a default value of 5 minutes
+is used.
+
@menu
* BINOMIAL:: Binomial Test
* CHISQUARE:: Chisquare Test
+* WILCOXON:: Wilcoxon Signed Ranks Test
@end menu
If no /EXPECTED subcommand is given, then then equal frequencies
are expected.
+@node WILCOXON
+@subsection Wilcoxon
+@comment node-name, next, previous, up
+@vindex WILCOXON
+@cindex wilcoxon matched pairs signed ranks test
+
+@display
+ [ /WILCOXON varlist [ WITH varlist [ (PAIRED) ]]]
+@end display
+
+The wilcoxon subcommand tests for differences between means of the
+variables listed. The test does not make any assumptions about the
+variances of the samples.
+
+If the @code{WITH} keyword is omitted, then tests for all
+combinations of the listed variables are performed.
+If the @code{WITH} keyword is given, and the @code{(PAIRED)} keyword
+is also given, then the number of variables preceding @code{WITH}
+must be the same as the number following it.
+In this case, tests for each respective pair of variables are
+performed.
+If the @code{WITH} keyword is given, but the
+@code{(PAIRED)} keyword is omitted, then tests for each combination
+of variable preceding @code{WITH} against variable following
+@code{WITH} are performed.
+
+If the number of observations is large, and exact tests have been
+requested. then the test may take a very long time to complete.
@node T-TEST
@comment node-name, next, previous, up
display a warning, but will proceed with the analysis.
The @code{CONTRAST} subcommand may be given up to 10 times in order
to specify different contrast tests.
-@setfilename ignored
@node RANK
@comment node-name, next, previous, up
INCLUDE means they are to be included. The default is EXCLUDE.
@include regression.texi
+
+
+@node RELIABILITY
+@section RELIABILITY
+
+@vindex RELIABILITY
+@display
+RELIABILITY
+ /VARIABLES=var_list
+ /SCALE (@var{name}) = @{var_list, ALL@}
+ /MODEL=@{ALPHA, SPLIT[(N)]@}
+ /SUMMARY=@{TOTAL,ALL@}
+ /MISSING=@{EXCLUDE,INCLUDE@}
+@end display
+
+@cindex Cronbach's Alpha
+The @cmd{RELIABILTY} command performs reliablity analysis on the data.
+
+The VARIABLES subcommand is required. It determines the set of variables
+upon which analysis is to be performed.
+
+The SCALE subcommand determines which variables reliability is to be
+calculated for. If it is omitted, then analysis for all variables named
+in the VARIABLES subcommand will be used.
+Optionally, the @var{name} parameter may be specified to set a string name
+for the scale.
+
+The MODEL subcommand determines the type of analysis. If ALPHA is specified,
+then Cronbach's Alpha is calculated for the scale. If the model is SPLIT,
+then the variables are divided into 2 subsets. An optional parameter
+@var{N} may be given, to specify how many variables to be in the first subset.
+If @var{N} is omitted, then it defaults to one half of the variables in the
+scale, or one half minus one if there are an odd number of variables.
+The default model is ALPHA.
+
+By default, any cases with user missing, or system missing values for
+any variables given
+in the VARIABLES subcommand will be omitted from analysis.
+The MISSING subcommand determines whether user missing values are to
+be included or excluded in the analysis.
+
+The SUMMARY subcommand determines the type of summary analysis to be performed.
+Currently there is only one type: SUMMARY=TOTAL, which displays per-item
+analysis tested against the totals.
+
+
+
projects / pspp-builds.git / blobdiff