FREQUENCIES: Simplify code for sorting the frequency table.

[pspp] / doc / invoking.texi

@node Invoking PSPP
@chapter Invoking @command{pspp}
@cindex invocation
@cindex PSPP, invoking

PSPP has two separate user interfaces.  This chapter describes
@command{pspp}, PSPP's command-line driven text-based user interface.
The following chapter briefly describes PSPPIRE, the graphical user
interface to PSPP.

The sections below describe the @command{pspp} program's command-line
interface.

@menu
* Main Options::                
* PDF PostScript and SVG Output Options::  
* Plain Text Output Options::   
* HTML Output Options::         
* OpenDocument Output Options::  
* Comma-Separated Value Output Options::  
@end menu

@node Main Options
@section Main Options

Here is a summary of all the options, grouped by type, followed by
explanations in the same order.

In the table, arguments to long options also apply to any
corresponding short options.

@table @emph
@item Non-option arguments
@example
@var{syntax-file}
@end example

@item Output options
@example
-o, --output=@var{output-file}
-O @var{option}=@var{value}
-O format=@var{format}
-O device=@{terminal|listing@}
-e, --error-file=@var{error-file}
@end example

@item Language options
@example
-I, --include=@var{dir}
-I-, --no-include
-i, --interactive
-r, --no-statrc
-a, --algorithm=@{compatible|enhanced@}
-x, --syntax=@{compatible|enhanced@}
@end example

@item Informational options
@example
-h, --help
-V, --version
@end example

@item Other options
@example
-s, --safer
--testing-mode
@end example
@end table

@table @code
@item @var{syntax-file}
Read and execute the named syntax file.  If no syntax files are
specified, PSPP prompts for commands.  If any syntax files are
specified, PSPP by default exits after it runs them, but you may make
it prompt for commands by specifying @samp{-} as an additional syntax
file.

@item -o @var{output-file}
Write output to @var{output-file}.  PSPP has several different output
drivers that support output in various formats (use @option{--help} to
list the available formats).  Specify this option more than once to
produce multiple output files, presumably in different formats.

Use @samp{-} as @var{output-file} to write output to standard output.

If no @option{-o} option is used, then PSPP writes output to standard
output in plain text format.

@item -O @var{option}=@var{value}
Sets an option for the output file configured by a preceding
@option{-o}.  Most options are specific to particular output formats.
A few options that apply generically are listed below.

@item -O format=@var{format}
PSPP uses the extension of the file name given on @option{-o} to
select an output format.  Use this option to override this choice by
specifying an alternate format, e.g.@: @option{-o pspp.out -O html} to
write HTML to a file named @file{pspp.out}.  Use @option{--help} to
list the available formats.

@item -O device=@{terminal|listing@}
Sets whether PSPP considers the output device configured by the
preceding @option{-o} to be a terminal or a listing device.  This
affects what output will be sent to the device, as configured by the
SET command's output routing subcommands (@pxref{SET}).  By default,
output written to standard output is considered a terminal device and
other output is considered a listing device.

@item -e @var{error-file}
@itemx --error-file=@var{error-file}
Configures a file to receive PSPP error, warning, and note messages in
plain text format.  Use @samp{-} as @var{error-file} to write messages
to standard output.  The default error file is standard output in the
absence of these options, but this is suppressed if an output device
writes to standard output (or another terminal), to avoid printing
every message twice.  Use @samp{none} as @var{error-file} to
explicitly suppress the default.

@item -I @var{dir}
@itemx --include=@var{dir}
Appends @var{dir} to the set of directories searched by INCLUDE
(@pxref{INCLUDE}) and INSERT (@pxref{INSERT}).

@item -I-
@itemx --no-include
Clears all directories from the include path, including directories
inserted in the include path by default.  The default include path is
@file{.} (the current directory), followed by @file{.pspp} in the
user's home directory, followed by PSPP's system configuration
directory (usually @file{/etc/pspp} or @file{/usr/local/etc/pspp}).

@item -i
@itemx --interactive
This option forces syntax files to be interpreted in interactive
mode, rather than the default batch mode.  @xref{Syntax Variants}, for
a description of the differences.

@item -r
@itemx --no-statrc
Disables running @file{rc} at PSPP startup time.

@item -a @{enhanced|compatible@}
@itemx --algorithm=@{enhanced|compatible@}
With @code{enhanced}, the default, PSPP uses the best implemented
algorithms for statistical procedures.  With @code{compatible},
however, PSPP will in some cases use inferior algorithms to produce
the same results as the proprietary program SPSS.

Some commands have subcommands that override this setting on a per
command basis.

@item -x @{enhanced|compatible@}
@itemx --syntax=@{enhanced|compatible@}
With @code{enhanced}, the default, PSPP accepts its own extensions
beyond those compatible with the proprietary program SPSS.  With
@code{compatible}, PSPP rejects syntax that uses these extensions.

@item -?
@itemx --help
Prints a message describing PSPP command-line syntax and the available
device formats, then exits.

@item -V
@itemx --version
Prints a brief message listing PSPP's version, warranties you don't
have, copying conditions and copyright, and e-mail address for bug
reports, then exits.

@item -s
@itemx --safer
Disables certain unsafe operations.  This includes the ERASE and
HOST commands, as well as use of pipes as input and output files.

@item --testing-mode
Invoke heuristics to assist with testing PSPP.  For use by @code{make
check} and similar scripts.
@end table

@node PDF PostScript and SVG Output Options
@section PDF, PostScript, and SVG Output Options

To produce output in PDF, PostScript, and SVG formats, specify
@option{-o @var{file}} on the PSPP command line, optionally followed
by any of the options shown in the table below to customize the output
format.

PDF, PostScript, and SVG output is only available if your installation
of PSPP was compiled with the Cairo library.

@table @code
@item -O format=@{pdf|ps|svg@}
Specify the output format.  This is only necessary if the file name
given on @option{-o} does not end in @file{.pdf}, @file{.ps}, or
@file{.svg}.

@item -O paper-size=@var{paper-size}
Paper size, as a name (e.g.@: @code{a4}, @code{letter}) or
measurements (e.g.@: @code{210x297}, @code{8.5x11in}).

The default paper size is taken from the @env{PAPERSIZE} environment
variable or the file indicated by the @env{PAPERCONF} environment
variable, if either variable is set.  If not, and your system supports
the @code{LC_PAPER} locale category, then the default paper size is
taken from the locale.  Otherwise, if @file{/etc/papersize} exists,
the default paper size is read from it.  As a last resort, A4 paper is
assumed.

@item -O orientation=@var{orientation}
Either @code{portrait} or @code{landscape}.  Default: @code{portrait}.

@item -O headers=@var{boolean}
When enabled, headers showing the time and date, title and subtitle,
and page number are printed at the top of each page.  Default:
@code{on}.

@item -O left-margin=@var{dimension}
@itemx -O right-margin=@var{dimension}
@itemx -O top-margin=@var{dimension}
@itemx -O bottom-margin=@var{dimension}
Sets the margins around the page.  The headers, if enabled, are not
included in the margins; they are in addition to the margins.  See
below for the allowed forms of @var{dimension} Default: @code{0.5in}.

@item -O prop-font=@var{font-name}
@itemx -O emph-font=@var{font-name}
@itemx -O fixed-font=@var{font-name}
Sets the font used for proportional, emphasized, or fixed-pitch text.
Most systems support CSS-like font names such as ``serif'' and
``monospace'', but a wide range of system-specific font are likely to
be supported as well.

Default: proportional font @code{serif}, emphasis font @code{serif
italic}, fixed-pitch font @code{monospace}.

@item -O font-size=@var{font-size}
Sets the size of the default fonts, in thousandths of a point.  Default:
10000 (10 point).

@item -O line-gutter=@var{dimension}
Sets the width of white space on either side of lines that border text
or graphics objects.  Default: @code{1pt}.

@item -O line-spacing=@var{dimension}
Sets the spacing between the lines in a double line in a table.
Default: @code{1pt}.

@item -O line-width=@var{dimension}
Sets the width of the lines used in tables.  Default: @code{0.5pt}.
@end table

Each @var{dimension} value above may be specified in various units
based on its suffix: @samp{mm} for millimeters, @samp{in} for inches,
or @samp{pt} for points.  Lacking a suffix, numbers below 50 are
assumed to be in inches and those about 50 are assumed to be in
millimeters.

@node Plain Text Output Options
@section Plain Text Output Options

PSPP can produce plain text output, drawing boxes using ASCII or
Unicode line drawing characters.  To produce plain text output,
specify @option{-o @var{file}} on the PSPP command line, optionally
followed by options from the table below to customize the output
format.

@table @code
@item -O format=txt
Specify the output format.  This is only necessary if the file name
given on @option{-o} does not end in @file{.txt} or @file{.list}.

@item -O charts=@{@var{template}.png|none@}
Name for chart files included in output.  The value should be a file
name that includes a single @samp{#} and ends in @file{png}.  When a
chart is output, the @samp{#} is replaced by the chart number.  The
default is the file name specified on @option{-o} with the extension
stripped off and replaced by @file{-#.png}.

Specify @code{none} to disable chart output.  Charts are always
disabled if your installation of PSPP was compiled without the
Cairo library.

@item -O paginate=@var{boolean}
If set, PSPP writes an ASCII formfeed the end of every page.  Default:
@code{off}.

@item -O headers=@var{boolean}
If enabled, PSPP prints two lines of header information giving title
and subtitle, page number, date and time, and PSPP version are printed
at the top of every page.  These two lines are in addition to any top
margin requested.  Default: @code{off}.

@item -O length=@var{line-count}
Physical length of a page.  Headers and margins are subtracted from
this value.  You may specify the number of lines as a number, or for
screen output you may specify @code{auto} to track the height of the
terminal as it changes.  Default: @code{66}.

@item -O width=@var{character-count}
Width of a page, in characters.  Margins are subtracted from this
value.  For screen output you may specify @code{auto} in place of a
number to track the width of the terminal as it changes.  Default:
@code{79}.

@item -O top-margin=@var{top-margin-lines}
Length of the top margin, in lines.  PSPP subtracts this value from
the page length.  Default: @code{0}.

@item -O bottom-margin=@var{bottom-margin-lines}
Length of the bottom margin, in lines.  PSPP subtracts this value from
the page length.  Default: @code{0}.

@item -O box[@var{line-type}]=@var{box-chars}
Sets the characters used for lines in tables.  @var{line-type} is a
4-digit number that indicates the type of line to change, in the order
`right', `bottom', `left', `top'.  Each digit is 0 for ``no line'', 1
for a single line, and 2 for a double line.  @var{box-chars} is the
character or string of characters to use for this type of line.

For example, @code{box[0101]="|"} sets @samp{|} as the character to
use for a single-width vertical line, and @code{box[1100]="\xda"} sets
@samp{"\xda"}, which on MS-DOS is suitable for the top-left corner of
a box, as the character for the intersection of two single-width
lines, one each from the right and bottom.

The defaults use @samp{-}, @samp{|}, and @samp{+} for single-width
lines and @samp{=} and @samp{#} for double-width lines.

@item -O init=@var{init-string}
If set, this string is written at the beginning of each output file.
It can be used to initialize device features, e.g.@: to enable VT100
line-drawing characters.

@item -O emphasis=@{none|bold|underline@}
How to emphasize text.  Bold and underline emphasis are achieved with
overstriking, which may not be supported by all the software to which
you might pass the output.  Default: @code{none}.
@end table

@node HTML Output Options
@section HTML Output Options

To produce output in HTML format, specify @option{-o @var{file}} on
the PSPP command line, optionally followed by any of the options shown
in the table below to customize the output format.

@table @code
@item -O format=html
Specify the output format.  This is only necessary if the file name
given on @option{-o} does not end in @file{.html}.

@item -O charts=@{@var{template}.png|none@}
Sets the name used for chart files.  @xref{Plain Text Output Options},
for details.
@end table

@node OpenDocument Output Options
@section OpenDocument Output Options

To produce output as an OpenDocument text (ODT) document, specify
@option{-o @var{file}} on the PSPP command line.  If @var{file} does
not end in @file{.odt}, you must also specify @option{-O format=odt}.

ODT support is only available if your installation of PSPP was
compiled with the libxml2 library.

The OpenDocument output format does not have any configurable options.

@node Comma-Separated Value Output Options
@section Comma-Separated Value Output Options

To produce output in comma-separated value (CSV) format, specify
@option{-o @var{file}} on the PSPP command line, optionally followed
by any of the options shown in the table below to customize the output
format.

@table @code
@item -O format=csv
Specify the output format.  This is only necessary if the file name
given on @option{-o} does not end in @file{.csv}.

@item -O separator=@var{field-separator}
Sets the character used to separate fields.  The default is a comma
(@samp{,}).
@end table

The CSV format used is an extension to that specified in RFC 4180:

@table @asis
@item Tables
Each table row is output on a separate line, and each column is output
as a field.  The contents of a cell that spans multiple rows or
columns is output only for the top-left row and column; the rest are
output as empty fields.  When a table has a caption, it is output just
above the table as a single field prefixed by @samp{Table:}.

@item Text
Text in output is printed as a field on a line by itself.  The TITLE
and SUBTITLE produce similar output, prefixed by @samp{Title:} or
@samp{Subtitle:}, respectively.

@item Messages
Errors, warnings, and notes are printed the same way as text.

@item Charts
Charts are not included in CSV output.
@end table

Successive output items are separated by a blank line.

@node Invoking PSPPIRE
@chapter Invoking @command{psppire}
@section The graphic user interface
@cindex Graphic user interface
@cindex PSPPIRE

The PSPPIRE graphic user interface for PSPP can perform all
functionality of the command line interface.  In addition it gives an
instantaneous view of the data, variables and statistical output.

The graphic user interface can be started by typing @command{psppire} at a 
command prompt.
Alternatively many systems have a system of interactive menus or buttons 
from which @command{psppire} can be started by a series of mouse clicks.

Once the principles of the PSPP system are understood, 
the graphic user interface is designed to be largely intuitive, and
for this reason is covered only very briefly by this manual.