Rename README.CVS to README.Git and update to refer to Git instead of CVS.

diff --git a/README.CVS b/README.CVS
deleted file mode 100644 (file)
index 2e45fef..0000000
--- a/README.CVS
+++ /dev/null
@@ -1,46 +0,0 @@
-To build this project from the sources direct from the cvs archive,
-you must install the prerequisites listed in README, plus the
-following:
-
-       * Autoconf 2.60 (or later).
-
-       * Automake 1.10 (or later).
-
-       * Gettext 0.17 (or later).
-
-       * GNU M4 1.4.9 (or later).
-
-       * pkg-config 0.21 (or later).
-
-        * gperf 3.0.1 (or later).
-
-       * Gnulib, from Git at <git://git.savannah.gnu.org/gnulib.git>.
-         If you do not have Git installed, up-to-date snapshots are
-         at <http://git.savannah.gnu.org/gitweb/?p=gnulib.git>.
-         Note that Gnulib does not require any form of installation:
-         simply checking it out into a directory is sufficient.  We
-         recommend checking out gnulib into a directory named `gnulib'
-          at the same level as PSPP.
-
-       * libtool 1.5.22 (or later).
-
-       * Texinfo 4.7 or later, to build the documentation.
-
-Once you have these installed, execute
-       make -f Smake
-If you checked Gnulib out in a directory named `gnulib' at the same
-level as PSPP, then this is sufficient.  Otherwise, provide the
-location of GNULIB on the `make' command line:
-       make -f Smake GNULIB=/gnulib/base/directory/name
-
-After executing Smake, you may configure the source tree in the usual
-way with ./configure, e.g.
-       ./configure
-For a list of options:
-       ./configure --help
-
-To test:
-       make check
-
-For a very thorough test: 
-       make distcheck

diff --git a/README.Git b/README.Git
new file mode 100644 (file)
index 0000000..b303b76
--- /dev/null
+++ b/README.Git
@@ -0,0 +1,46 @@
+To build this project from the sources direct from the Git archive,
+you must install the prerequisites listed in README, plus the
+following:
+
+       * Autoconf 2.60 (or later).
+
+       * Automake 1.10 (or later).
+
+       * Gettext 0.17 (or later).
+
+       * GNU M4 1.4.9 (or later).
+
+       * pkg-config 0.21 (or later).
+
+        * gperf 3.0.1 (or later).
+
+       * Gnulib, from Git at <git://git.savannah.gnu.org/gnulib.git>.
+         If you do not have Git installed, up-to-date snapshots are
+         at <http://git.savannah.gnu.org/gitweb/?p=gnulib.git>.
+         Note that Gnulib does not require any form of installation:
+         simply checking it out into a directory is sufficient.  We
+         recommend checking out gnulib into a directory named `gnulib'
+          at the same level as PSPP.
+
+       * libtool 1.5.22 (or later).
+
+       * Texinfo 4.7 or later, to build the documentation.
+
+Once you have these installed, execute
+       make -f Smake
+If you checked Gnulib out in a directory named `gnulib' at the same
+level as PSPP, then this is sufficient.  Otherwise, provide the
+location of GNULIB on the `make' command line:
+       make -f Smake GNULIB=/gnulib/base/directory/name
+
+After executing Smake, you may configure the source tree in the usual
+way with ./configure, e.g.
+       ./configure
+For a list of options:
+       ./configure --help
+
+To test:
+       make check
+
+For a very thorough test: 
+       make distcheck