#include "mmu.h"
+#include "loader.h"
-###################################################################################
-# ENTRY POINT
-# This code should be stored in the first sector of the hard disk. When the
-# BIOS runs, it loads this code at physical address 0x7c00 - 0x7e00 (512 bytes).
-# Then jumps to the beginning of it, in real-mode (BIOS runs in real mode).
-#
+##############################################################################
+# Kernel loader.
+#
+# This code should be stored in the first sector of the hard disk. When the
+# BIOS runs, it loads this code at physical address 0x7c00-0x7e00 (512 bytes).
+# Then it jumps to the beginning of it, in real mode.
# This code switches into protected mode (32-bit mode) so that all of
-# memory can accessed, then calls into C.
-###################################################################################
+# memory can accessed, loads the kernel into memory, and jumps to the
+# first byte of the kernel, where start.S is linked.
+##############################################################################
.globl start # Entry point
start: .code16 # This runs in real mode
#### Returns CF clear if successful, with AX = (kB of physical memory) - 1024.
#### This only works for memory sizes <= 65 MB, which should be fine for our purposes.
- movb $0x88,%ah
- int $0x15
- jc panic # Carry flag set on error
- addl $1024,%eax # Total kB
- shrl $2,%eax # Total 4 kB pages
- movl %eax, ram_pages
+ movb $0x88,%ah
+ int $0x15
+ jc panic # Carry flag set on error
+2: addl $1024,%eax # Total kB
+ shrl $2,%eax # Total 4 kB pages
+ movl %eax, ram_pages
#### switch from real to protected mode
#### The segments in GDT allow all of physical memory to be accessed.
movl %cr0, %eax # turn on protected mode
orl $CR0_PE, %eax #
movl %eax, %cr0 #
- ### CPU magic: jump to relocation, flush prefetch queue, and reload %cs
- ### Has the effect of just jmp to the next instruction, but simultaneous
- ### loads CS with $PROT_MODE_CSEG.
+ ### CPU magic: jump to relocation, flush prefetch queue, and
+ ### reload %cs Has the effect of just jmp to the next
+ ### instruction, but simultaneous loads CS with
+ ### $PROT_MODE_CSEG.
ljmp $SEL_KCSEG, $protcseg
#### We are in protected mode in a 32-bit segment (hence the .code32)
movw %ax, %gs
movw %ax, %ss
-#### Load kernel at 1 MB by frobbing the IDE controller directly.
+#### Load kernel starting at physical address LOADER_KERN_BASE by
+#### frobbing the IDE controller directly.
movl $1, %ebx
- movl $0x100000, %edi
+ movl $LOADER_KERN_BASE, %edi
read_sector:
### Poll status register while controller busy.
cmpl $KERNEL_LOAD_PAGES*8 + 1, %ebx
jnz read_sector
-##### Create temporary PDE and PTE and set page directory pointer
+##### Create temporary PDE and PTE, set page directory pointer, and turn
+##### on paging.
##### FIXME? We could use a single 4 MB page instead of 1024 4 kB pages.
- movl $0x10000, %edi
+ # Create PDE at 64 kB.
+ movl $0x10000, %edi
movl %edi, %cr3
+
+ # Fill PDE with zeroes.
subl %eax, %eax
movl $0x400, %ecx
rep stosl
+
+ # Set PDE entries for 0 and LOADER_PHYS_BASE to point to the
+ # PTE.
movl $0x11000 | PG_U | PG_W | PG_P, %eax
movl %eax, 0x10000
- movl %eax, 0x10c00
+ movl %eax, 0x10000 | (LOADER_PHYS_BASE >> 20)
+
+ # Initialize PTE.
movl $PG_U | PG_W | PG_P, %eax
movl $0x400, %ecx
1: stosl
addl $0x1000, %eax
loop 1b
-##### Enable paging.
-
+ # Enable paging.
movl %cr0, %eax
orl $CR0_PG, %eax
movl %eax, %cr0
##### Jump to kernel entry point.
- movl $0xc0007c00, %esp
- movl $0xc0100000, %eax
+ movl $LOADER_PHYS_BASE + LOADER_BASE, %esp
+ movl $LOADER_PHYS_BASE + LOADER_KERN_BASE, %eax
jmp *%eax
##### GDT
.word 0x17 # sizeof (gdt) - 1
.long gdt # address gdt
-##### Arrive here on error
-panic: jmp panic
+##### To panic, we print panicmsg (with help from the BIOS) and spin.
+panic: .code16 # We only panic in real mode.
+ movw $panicmsg, %si
+ movb $0xe, %ah
+ xorb %bh, %bh
+1: lodsb
+ test %al, %al
+2: jz 2b # Spin.
+ int $0x10
+ jmp 1b
+
+panicmsg:
+ .ascii "Loader panic!\r\n"
+ .byte 0
##### Memory size in 4 kB pages.
- .org 0x200 - 8
+ .org LOADER_RAM_PAGES
ram_pages:
.long 0
+##### Command-line arguments inserted by another utility.
+##### The loader doesn't use these, but we note their
+##### location here for easy reference.
+ .org LOADER_CMD_LINE
+cmd_line:
+ .fill 0x80, 1, 0
+
##### Boot-sector signature for BIOS inspection.
- .org 0x200 - 2
+ .org LOADER_BIOS_SIG
.word 0xaa55