X-Git-Url: https://pintos-os.org/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=vswitchd%2Fvswitch.xml;h=e9ea0c4c73a2d1e79eeaf946fa618c932daba3c4;hb=4206b80f6444ceef47ceb9e1a6b88a40eabacb1f;hp=688f7157221619b8cfbbba2c781e17d4ccbe03d6;hpb=fd0ca62bb10b92ba383f2ee6aa51863273bb38ff;p=openvswitch

diff --git a/vswitchd/vswitch.xml b/vswitchd/vswitch.xml
index 688f7157..e9ea0c4c 100644
--- a/vswitchd/vswitch.xml
+++ b/vswitchd/vswitch.xml
@@ -569,21 +569,13 @@
           <dt><code>01:80:c2:00:00:0<var>x</var></code></dt>
           <dd>Other reserved protocols.</dd>
 
-          <dt><code>00:00:5e:00:01:<var>x</var><var>x</var></code></dt>
-          <dd> VRRP IPv4 virtual router MAC address. </dd>
+          <dt><code>00:e0:2b:00:00:00</code></dt>
+          <dd>Extreme Discovery Protocol (EDP).</dd>
 
-          <dt><code>00:00:5e:00:02:<var>x</var><var>x</var></code></dt>
-          <dd> VRRP IPv6 virtual router MAC address. </dd>
-
-          <dt><code>00:00:0c:07:ac:<var>x</var><var>x</var></code></dt>
-          <dd> HSRP Version 1. </dd>
-
-          <dt><code>00:00:0c:9f:f<var>x</var>:<var>x</var><var>x</var></code>
-          </dt>
-          <dd> HSRP Version 2. </dd>
-
-          <dt><code>00:07:b4:<var>x</var><var>x</var>:<var>x</var><var>x</var>:<var>x</var><var>x</var></code></dt>
-          <dd> GLBP. </dd>
+          <dt>
+	    <code>00:e0:2b:00:00:04</code> and <code>00:e0:2b:00:00:06</code>
+	  </dt>
+          <dd>Ethernet Automatic Protection Switching (EAPS).</dd>
 
           <dt><code>01:00:0c:cc:cc:cc</code></dt>
           <dd>
@@ -600,6 +592,9 @@
 
           <dt><code>01:00:0c:00:00:00</code></dt>
           <dd>Cisco Inter Switch Link.</dd>
+
+          <dt><code>01:00:0c:cc:cc:c<var>x</var></code></dt>
+          <dd>Cisco CFM.</dd>
         </dl>
       </column>
 
@@ -807,8 +802,13 @@
 
     <group title="Bonding Configuration">
       <p>A port that has more than one interface is a ``bonded port.'' Bonding
-      allows for load balancing and fail-over.  Some kinds of bonding will
-      work with any kind of upstream switch:</p>
+      allows for load balancing and fail-over.</p>
+
+      <p>
+        The following types of bonding will work with any kind of upstream
+        switch.  On the upstream switch, do not configure the interfaces as a
+        bond:
+      </p>
 
       <dl>
         <dt><code>balance-slb</code></dt>
@@ -820,7 +820,8 @@
         <dt><code>active-backup</code></dt>
         <dd>
           Assigns all flows to one slave, failing over to a backup slave when
-          the active slave is disabled.
+          the active slave is disabled.  This is the only bonding mode in which
+          interfaces may be plugged into different upstream switches.
         </dd>
       </dl>
 
@@ -839,6 +840,7 @@
 
         <dt><code>stable</code></dt>
         <dd>
+          <p>Deprecated and slated for removal in February 2013.</p>
           <p>Attempts to always assign a given flow to the same slave
           consistently.  In an effort to maintain stability, no load
           balancing is done.  Uses a similar hashing strategy to
@@ -895,7 +897,7 @@
 
         <column name="bond_updelay">
           <p>
-            The number of milliseconds for which carrier must stay up on an
+            The number of milliseconds for which the link must stay up on an
             interface before the interface is considered to be up.  Specify
             <code>0</code> to enable the interface immediately.
           </p>
@@ -908,7 +910,7 @@
         </column>
 
         <column name="bond_downdelay">
-          The number of milliseconds for which carrier must stay down on an
+          The number of milliseconds for which the link must stay down on an
           interface before the interface is considered to be down.  Specify
           <code>0</code> to disable the interface immediately.
         </column>
@@ -961,12 +963,10 @@
         </column>
       </group>
 
-      <group title="SLB Configuration">
+      <group title="Rebalancing Configuration">
         <p>
           These settings control behavior when a bond is in
-          <code>balance-slb</code> mode, regardless of whether the bond was
-          intentionally configured in SLB mode or it fell back to SLB mode
-          because LACP negotiation failed.
+          <code>balance-slb</code> or <code>balance-tcp</code> mode.
         </p>
 
         <column name="other_config" key="bond-rebalance-interval"
@@ -975,7 +975,7 @@
           successive attempts to rebalance the bond, that is, to move flows
           from one interface on the bond to another in an attempt to keep usage
           of each interface roughly equal.  If zero, load balancing is disabled
-          on the bond (carrier status changes still cause flows to move).  If
+          on the bond (link failure still cause flows to move).  If
           less than 1000ms, the rebalance interval will be 1000ms.
         </column>
       </group>
@@ -1199,6 +1199,21 @@
             IPsec tunnel.
           </dd>
 
+          <dt><code>gre64</code></dt>
+          <dd>
+            It is same as GRE, but it allows 64 bit key. To store higher 32-bits
+            of key, it uses GRE protocol sequence number field. This is non
+            standard use of GRE protocol since OVS does not increment
+            sequence number for every packet at time of encap as expected by
+            standard GRE implementation. See <ref group="Tunnel Options"/>
+            for information on configuring GRE tunnels.
+          </dd>
+
+          <dt><code>ipsec_gre64</code></dt>
+          <dd>
+            Same as IPSEC_GRE except 64 bit key.
+          </dd>
+
           <dt><code>capwap</code></dt>
           <dd>
             An Ethernet tunnel over the UDP transport portion of CAPWAP (RFC
@@ -1215,7 +1230,8 @@
           </dd>
 
           <dt><code>null</code></dt>
-          <dd>An ignored interface.</dd>
+          <dd>An ignored interface. Deprecated and slated for removal in
+              February 2013.</dd>
         </dl>
       </column>
     </group>
@@ -1223,7 +1239,8 @@
     <group title="Tunnel Options">
       <p>
         These options apply to interfaces with <ref column="type"/> of
-        <code>gre</code>, <code>ipsec_gre</code>, and <code>capwap</code>.
+        <code>gre</code>, <code>ipsec_gre</code>, <code>gre64</code>,
+        <code>ipsec_gre64</code>, and <code>capwap</code>.
       </p>
 
       <p>
@@ -1701,6 +1718,12 @@
         faulted otherwise.
       </p>
 
+      <p>
+          When operating over tunnels which have no <code>in_key</code>, or an
+          <code>in_key</code> of <code>flow</code>.  CFM will only accept CCMs
+          with a tunnel key of zero.
+      </p>
+
       <column name="cfm_mpid">
         A Maintenance Point ID (MPID) uniquely identifies each endpoint within
         a Maintenance Association.  The MPID is used to identify this endpoint
@@ -1769,6 +1792,13 @@
         frame having an invalid interval.
       </column>
 
+      <column name="cfm_remote_opstate">
+        <p>When in extended mode, indicates the operational state of the
+          remote endpoint as either <code>up</code> or <code>down</code>.  See
+          <ref column="other_config" key="cfm_opstate"/>.
+        </p>
+      </column>
+
       <column name="cfm_health">
         <p>
           Indicates the health of the interface as a percentage of CCM frames
@@ -1849,7 +1879,7 @@
       <column name="other_config" key="cfm_ccm_pcp"
         type='{"type": "integer", "minInteger": 1, "maxInteger": 7}'>
         When set, the CFM module will apply a VLAN tag to all CCMs it generates
-        with the given PCP value.  The VLAN ID of the tag is governed by the
+        with the given PCP value, the VLAN ID of the tag is governed by the
         value of <ref column="other_config" key="cfm_ccm_vlan"/>. If
         <ref column="other_config" key="cfm_ccm_vlan"/> is unset, a VLAN ID of
         zero is used.
@@ -2124,7 +2154,7 @@
       <p>
         The eviction process only considers flows that have an idle timeout or
         a hard timeout.  That is, eviction never deletes permanent flows.
-        (Permanent flows do count against <ref column="flow_limit"/>.
+        (Permanent flows do count against <ref column="flow_limit"/>.)
       </p>
 
       <p>