X-Git-Url: https://pintos-os.org/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=vswitchd%2Fvswitch.xml;h=688f7157221619b8cfbbba2c781e17d4ccbe03d6;hb=5d03d2a76510db1d22779154904bc23d12b297e7;hp=ef019746cee4489b7392fb30e0b0dc6aabe1607c;hpb=cea157688977bbbb136f9c3bfe020fe485b43d39;p=openvswitch diff --git a/vswitchd/vswitch.xml b/vswitchd/vswitch.xml index ef019746..688f7157 100644 --- a/vswitchd/vswitch.xml +++ b/vswitchd/vswitch.xml @@ -409,7 +409,16 @@ any defined controllers forever.
-If this value is unset, the default is implementation-specific.
+
+ The default is standalone
if the value is unset, but
+ future versions of Open vSwitch may change the default.
+
+ The standalone
mode can create forwarding loops on a
+ bridge that has more than one uplink port unless STP is enabled. To
+ avoid loops on such a bridge, configure secure
mode or
+ enable STP (see ).
+
When more than one controller is configured, is considered only when none of the configured controllers can be contacted.
@@ -547,6 +556,51 @@ and if Open vSwitch node does not run STP, then this option should be enabled. Default is disabled, set totrue
to enable.
+
+ The following destination MAC addresss will not be forwarded when this
+ option is enabled.
+ 01:80:c2:00:00:00
01:80:c2:00:00:01
01:80:c2:00:00:0x
00:00:5e:00:01:xx
00:00:5e:00:02:xx
00:00:0c:07:ac:xx
00:00:0c:9f:fx:xx
+ 00:07:b4:xx:xx:xx
01:00:0c:cc:cc:cc
01:00:0c:cc:cc:cd
01:00:0c:cd:cd:cd
01:00:0c:00:00:00
The LACP timing which should be used on this .
- Possible values are fast
, slow
and a
- positive number of milliseconds. By default slow
is
- used. When configured to be fast
LACP heartbeats are
- requested at a rate of once per second causing connectivity
- problems to be detected more quickly. In slow
mode,
- heartbeats are requested at a rate of once every 30 seconds.
-
- Users may manually set a heartbeat transmission rate to increase
- the fault detection speed further. When manually set, OVS expects
- the partner switch to be configured with the same transmission
- rate. Manually setting lacp-time
to something other
- than fast
or slow
is not supported by the
- LACP specification.
+ By default slow
is used. When configured to be
+ fast
LACP heartbeats are requested at a rate of once
+ per second causing connectivity problems to be detected more
+ quickly. In slow
mode, heartbeats are requested at a
+ rate of once every 30 seconds.
false
.
- inherit
, in which case
+ packet. ToS is interpreted as DSCP and ECN bits, ECN part must be
+ zero. It may also be the word inherit
, in which case
the ToS will be copied from the inner packet if it is IPv4 or IPv6
(otherwise it will be 0). The ECN fields are always inherited.
Default is 0.
@@ -1731,11 +1769,6 @@
frame having an invalid interval.
Indicates the health of the interface as a percentage of CCM frames
@@ -1767,9 +1800,21 @@
+ The interval, in milliseconds, between transmissions of CFM
+ heartbeats. Three missed heartbeat receptions indicate a
+ connectivity fault.
+
+ In standard operation only intervals of 3, 10, 100, 1,000, 10,000,
+ 60,000, or 600,000 ms are supported. Other values will be rounded
+ down to the nearest value on the list. Extended mode (see ) supports any interval up
+ to 65,535 ms. In either mode, the default is 1000 ms.
+ We do not recommend using intervals less than 100 ms.
+ Hypervisors may sometimes have more than one interface associated
+ with a given , only one of
+ which is actually in use at a given time. For example, in some
+ circumstances XenServer has both a ``tap'' and a ``vif'' interface
+ for a single , but only
+ uses one of them at a time. A hypervisor that behaves this way must
+ mark the currently in use interface active
and the
+ others inactive
. A hypervisor that never has more than
+ one interface for a given
+ may mark that interface active
or omit entirely.
+
+ During VM migration, a given might transiently be marked active
on
+ two different hypervisors. That is, active
means that
+ this is the active
+ instance within a single hypervisor, not in a broader scope.
+
- The following destination MAC addresses will not be mirrored to a - VLAN to avoid confusing switches that interpret the protocols that - they represent: + See the documentation for + in the + table for a list of destination MAC + addresses which will not be mirrored to a VLAN to avoid confusing + switches that interpret the protocols that they represent.
-01:80:c2:00:00:00
01:80:c2:00:00:01
01:80:c2:00:00:0x
01:00:0c:cc:cc:cc
01:00:0c:cc:cc:cd
01:00:0c:cd:cd:cd
01:00:0c:00:00:00
Please note: Mirroring to a VLAN can disrupt a network that contains unmanaged switches. Consider an unmanaged physical switch with two ports: port 1, connected to an end host, and port 2, @@ -2704,10 +2751,9 @@ Service (QoS) on IP networks. The DSCP value specified here is used when establishing the connection - between the controller and the Open vSwitch. The connection must be - reset for the new DSCP values to take effect. If no value is - specified, a default value of 48 is chosen. Valid DSCP values must be - in the range 0 to 63. + between the controller and the Open vSwitch. If no value is specified, + a default value of 48 is chosen. Valid DSCP values must be in the + range 0 to 63.