X-Git-Url: https://pintos-os.org/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=vswitchd%2Fvswitch.xml;h=6565b9582e6ab898b5b914ac9e679d6dcb599f73;hb=ea7bd5973fb426f3a6ea66b0953c6000980e77ec;hp=8b2221b83450de9d5d6fa44d564c82f1ad90e867;hpb=9a3f4a496f9772b65562044f722536cd6270f698;p=openvswitch
diff --git a/vswitchd/vswitch.xml b/vswitchd/vswitch.xml
index 8b2221b8..6565b958 100644
--- a/vswitchd/vswitch.xml
+++ b/vswitchd/vswitch.xml
@@ -16,11 +16,6 @@
Set of bridges managed by the daemon.
-
- Remote database clients to which the Open vSwitch's database server
- should connect or to which it should listen.
-
-
SSL used globally by the daemon.
@@ -33,12 +28,6 @@
choose key names that are likely to be unique. The currently
defined common key-value pairs are:
- system-type
- - An identifier for the switch type, such as
-
XenServer
or KVM
.
- system-version
- - The version of the switch software, such as
-
5.6.0
on XenServer.
system-id
- A unique identifier for the Open vSwitch's physical host.
The form of the identifier depends on the type of the host.
@@ -205,6 +194,101 @@
+
+
+
+ These columns report the types and versions of the hardware and
+ software running Open vSwitch. We recommend in general that software
+ should test whether specific features are supported instead of relying
+ on version number checks. These values are primarily intended for
+ reporting to human administrators.
+
+
+
+ The Open vSwitch version number, e.g. 1.1.0pre2
.
+ If Open vSwitch was configured with a build number, then it is
+ also included, e.g. 1.1.0pre2+build4948
.
+
+
+
+
+ The database schema version number in the form
+ major.minor.tweak
,
+ e.g. 1.2.3
. Whenever the database schema is changed in
+ a non-backward compatible way (e.g. deleting a column or a table),
+ major is incremented. When the database schema is changed
+ in a backward compatible way (e.g. adding a new column),
+ minor is incremented. When the database schema is changed
+ cosmetically (e.g. reindenting its syntax), tweak is
+ incremented.
+
+
+
+ The schema version is part of the database schema, so it can also be
+ retrieved by fetching the schema using the Open vSwitch database
+ protocol.
+
+
+
+
+
+ An identifier for the type of system on top of which Open vSwitch
+ runs, e.g. XenServer
or KVM
.
+
+
+ System integrators are responsible for choosing and setting an
+ appropriate value for this column.
+
+
+
+
+
+ The version of the system identified by ,
+ e.g. 5.5.0-24648p
on XenServer 5.5.0 build 24648.
+
+
+ System integrators are responsible for choosing and setting an
+ appropriate value for this column.
+
+
+
+
+
+
+
+ These columns primarily configure the Open vSwitch database
+ (ovsdb-server
), not the Open vSwitch switch
+ (ovs-vswitchd
). The OVSDB database also uses the settings.
+
+
+
+ The Open vSwitch switch does read the database configuration to
+ determine remote IP addresses to which in-band control should apply.
+
+
+
+ Database clients to which the Open vSwitch database server should
+ connect or to which it should listen, along with options for how these
+ connection should be configured. See the table
+ for more information.
+
+
+
+
+ Remote database clients to which the Open vSwitch's database server
+ should connect or to which it should listen. Adding an OVSDB target
+ to this set is equivalent to adding it to with all of the default options.
+
+
+
+ Use of this column is deprecated and may be removed sometime in the
+ future. New applications should use and set instead.
+
+
+
@@ -283,7 +367,7 @@
If this value is unset, the default is implementation-specific.
- When more than one controller is configured,
+
When more than one controller is configured,
is considered only when none of the
configured controllers can be contacted.
@@ -312,7 +396,7 @@
defined key-value pairs are:
bridge-id
- - A unique identifier of the bridge. On Citrix XenServer this
+
- A unique identifier of the bridge. On Citrix XenServer this
will commonly be the same as
xs-network-uuids
.
xs-network-uuids
- Semicolon-delimited set of universally unique identifier(s) for
@@ -329,12 +413,23 @@
datapath-id
- Exactly 16 hex
digits to set the OpenFlow datapath ID to a specific
- value.
+ value. May not be all-zero.
+ disable-in-band
+ - If set to
true
, disable in-band control on
+ the bridge regardless of controller and manager settings.
hwaddr
- An Ethernet address in the form
xx:xx:xx:xx:xx:xx
to set the hardware address of the local port and influence the
datapath ID.
+ in-band-queue
+ -
+ A queue ID as a nonnegative integer. This sets the OpenFlow queue
+ ID that will be used by flows set up by in-band control on this
+ bridge. If unset, or if the port used by an in-band control flow
+ does not have QoS configured, or if the port does not have a queue
+ with the specified ID, the default queue is used instead.
+
@@ -412,18 +507,25 @@
- A port that has more than one interface is a ``bonded port.''
- Bonding allows for load balancing and fail-over. Open vSwitch
- supports ``source load balancing'' (SLB) bonding, which
- assigns flows to slaves based on source MAC address, with
- periodic rebalancing as traffic patterns change. This form of
- bonding does not require 802.3ad or other special support from
- the upstream switch to which the slave devices are
- connected.
+ A port that has more than one interface is a ``bonded port.'' Bonding
+ allows for load balancing and fail-over. Open vSwitch supports
+ ``source load balancing'' (SLB) and "active backup" bonding. SLB
+ bonding assigns flows to slaves based on source MAC address and output
+ VLAN, with periodic rebalancing as traffic patterns change. Active
+ backup bonding assigns all flows to one slave, failing over to a backup
+ slave when the active slave is disabled. Neither form of bonding
+ require 802.3ad or other special support from the upstream switch to
+ which the slave devices are connected.
These columns apply only to bonded ports. Their values are
otherwise ignored.
+
+ The type of bonding used for a bonded port. Currently supported
+ values are balance-slb
and active-backup
.
+ Defaults to SLB if unset.
+
+
For a bonded port, the number of milliseconds for which carrier must
stay up on an interface before the interface is considered to be up.
@@ -450,7 +552,7 @@
Quality of Service configuration for this port.
-
+
The MAC address to use for this port for the purpose of choosing the
bridge's MAC address. This column does not necessarily reflect the
@@ -489,12 +591,22 @@
An Ethernet address in the form
xx:xx:xx:xx:xx:xx
.
bond-rebalance-interval
- For a bonded port, the number of milliseconds between
+ For an SLB bonded port, the number of milliseconds between
successive attempts to rebalance the bond, that is, to
move source MACs and their flows from one interface on
the bond to another in an attempt to keep usage of each
interface roughly equal. The default is 10000 (10
seconds), and the minimum is 1000 (1 second).
+ bond-detect-mode
+ Sets the method used to detect link failures in a bonded port.
+ Options are carrier
and miimon
. Defaults
+ to carrier
which uses each interface's carrier to detect
+ failures. When set to miimon
, will check for failures
+ by polling each interface's MII.
+ bond-miimon-interval
+ The number of milliseconds between successive attempts to
+ poll each interface's MII. Only relevant on ports which use
+ miimon
to detect failures.
@@ -539,7 +651,7 @@
Open vSwitch populates this column when the port number becomes
known. If the interface is successfully added,
will be set to a number between 1 and 65535
- (generally either in the range 1 to 65280, exclusive, or 65534, the
+ (generally either in the range 1 to 65279, inclusive, or 65534, the
port number for the OpenFlow ``local port''). If the interface
cannot be added then Open vSwitch sets this column
to -1.
@@ -573,7 +685,7 @@
the same except one has an optional identifier and the other does
not, the more specific one is matched first. in_key
is considered more specific than local_ip
if a port
- defines one and another port defines the other. The following
+ defines one and another port defines the other. The following
options may be specified in the column:
remote_ip
@@ -661,9 +773,122 @@
bypass certain components of the IP stack (such as IP tables)
and it may be useful to disable it if these features are
required or as a debugging measure. Default is enabled, set to
- false
to disable. If IPsec is enabled through the
- parameters, header caching will be
- automatically disabled.
+ false
to disable.
+
+
+ ipsec_gre
+ An Ethernet over RFC 2890 Generic Routing Encapsulation
+ over IPv4 IPsec tunnel. Each tunnel (including those of type
+ gre
) must be uniquely identified by the
+ combination of remote_ip
and
+ local_ip
. Note that if two ports are defined
+ that are the same except one has an optional identifier and
+ the other does not, the more specific one is matched first.
+ An authentication method of peer_cert
or
+ psk
must be defined. The following options may
+ be specified in the column:
+
+ remote_ip
+ - Required. The tunnel endpoint.
+
+
+ local_ip
+ - Optional. The destination IP that received packets must
+ match. Default is to match all addresses.
+
+
+ peer_cert
+ - Required for certificate authentication. A string
+ containing the peer's certificate in PEM format.
+ Additionally the host's certificate must be specified
+ with the
certificate
option.
+
+
+ certificate
+ - Required for certificate authentication. The name of a
+ PEM file containing a certificate that will be presented
+ to the peer during authentication.
+
+
+ private_key
+ - Optional for certificate authentication. The name of
+ a PEM file containing the private key associated with
+
certificate
. If certificate
+ contains the private key, this option may be omitted.
+
+
+ psk
+ - Required for pre-shared key authentication. Specifies a
+ pre-shared key for authentication that must be identical on
+ both sides of the tunnel.
+
+
+ in_key
+ - Optional. The GRE key that received packets must contain.
+ It may either be a 32-bit number (no key and a key of 0 are
+ treated as equivalent) or the word
flow
. If
+ flow
is specified then any key will be accepted
+ and the key will be placed in the tun_id
field
+ for matching in the flow table. The ovs-ofctl manual page
+ contains additional information about matching fields in
+ OpenFlow flows. Default is no key.
+
+
+ out_key
+ - Optional. The GRE key to be set on outgoing packets. It may
+ either be a 32-bit number or the word
flow
. If
+ flow
is specified then the key may be set using
+ the set_tunnel
Nicira OpenFlow vendor extension (0
+ is used in the absence of an action). The ovs-ofctl manual
+ page contains additional information about the Nicira OpenFlow
+ vendor extensions. Default is no key.
+
+
+ key
+ - Optional. Shorthand to set
in_key
and
+ out_key
at the same time.
+
+
+ tos
+ - Optional. The value of the ToS bits to be set on the
+ encapsulating packet. It may also be the word
+
inherit
, in which case the ToS will be copied from
+ the inner packet if it is IPv4 or IPv6 (otherwise it will be
+ 0). Note that the ECN fields are always inherited. Default is
+ 0.
+
+
+ ttl
+ - Optional. The TTL to be set on the encapsulating packet.
+ It may also be the word
inherit
, in which case the
+ TTL will be copied from the inner packet if it is IPv4 or IPv6
+ (otherwise it will be the system default, typically 64).
+ Default is the system default TTL.
+
+
+ csum
+ - Optional. Compute GRE checksums on outgoing packets.
+ Checksums present on incoming packets will be validated
+ regardless of this setting. Note that GRE checksums
+ impose a significant performance penalty as they cover the
+ entire packet. As the contents of the packet is typically
+ covered by L3 and L4 checksums, this additional checksum only
+ adds value for the GRE and encapsulated Ethernet headers.
+ Default is disabled, set to
true
to enable.
+
+
+ pmtud
+ - Optional. Enable tunnel path MTU discovery. If enabled
+ ``ICMP destination unreachable - fragmentation'' needed
+ messages will be generated for IPv4 packets with the DF bit set
+ and IPv6 packets above the minimum MTU if the packet size
+ exceeds the path MTU minus the size of the tunnel headers. It
+ also forces the encapsulating packet DF bit to be set (it is
+ always set if the inner packet implies path MTU discovery).
+ Note that this option causes behavior that is typically
+ reserved for routers and therefore is not entirely in
+ compliance with the IEEE 802.1D specification for bridges.
+ Default is enabled, set to
false
to disable.
capwap
@@ -757,18 +982,91 @@
Configuration options whose interpretation varies based on
.
+
+
+
+
+ Status information about interfaces attached to bridges, updated every
+ 5 seconds. Not all interfaces have all of these properties; virtual
+ interfaces don't have a link speed, for example. Non-applicable
+ columns will have empty values.
+
+
+
+ The administrative state of the physical network link.
+
+
+
+
+
+ The observed state of the physical network link;
+ i.e. whether a carrier is detected by the interface.
+
+
+
+
+
+ The negotiated speed of the physical network link.
+ Valid values are positive integers greater than 0.
+
+
+
+
+
+ The duplex mode of the physical network link.
+
+
+
+
+
+ The MTU (maximum transmission unit); i.e. the largest
+ amount of data that can fit into a single Ethernet frame.
+ The standard Ethernet MTU is 1500 bytes. Some physical media
+ and many kinds of virtual interfaces can be configured with
+ higher MTUs.
+
+
Key-value pairs that report port status. Supported status
- values are type
-dependent.
+ values are type
-dependent; some interfaces may not have
+ a valid driver_name
, for example.
- The only currently defined key-value pair is:
+ The currently defined key-value pairs are:
+
+ driver_name
+ - The name of the device driver controlling the network
+ adapter.
+
+
+ driver_version
+ - The version string of the device driver controlling the
+ network adapter.
+
+
+ firmware_version
+ - The version string of the network adapter's firmware, if
+ available.
+
source_ip
- The source IP address used for an IPv4 tunnel end-point,
- such as
gre
or capwap
. Not
- supported by all implementations.
+ such as gre
or capwap
.
+
+
+ tunnel_egress_iface
+ - Egress interface for tunnels. Currently only relevant for GRE
+ and CAPWAP tunnels. On Linux systems, this column will show
+ the name of the interface which is responsible for routing
+ traffic destined for the configured
remote_ip
.
+ This could be an internal interface such as a bridge port.
+
+
+ tunnel_egress_iface_carrier
+ - Whether a carrier is detected on
. Valid values are down
+ and up
.
@@ -850,6 +1148,11 @@
+
+
+ Connectivity monitor configuration for this interface.
+
+
Key-value pairs for use by external frameworks that integrate
with Open vSwitch, rather than by Open vSwitch itself. System
@@ -866,7 +1169,7 @@
For Citrix XenServer, this is the value of the MAC
field in the VIF record for this interface.
iface-id
- A system-unique identifier for the interface. On XenServer,
+ A system-unique identifier for the interface. On XenServer,
this will commonly be the same as xs-vif-uuid
.
@@ -892,23 +1195,7 @@
Key-value pairs for rarely used interface features. Currently,
- the only keys are for configuring GRE-over-IPsec, which is only
- available through the openvswitch-ipsec
package for
- Debian. The currently defined key-value pairs are:
-
- ipsec_local_ip
- - Required key for GRE-over-IPsec interfaces. Additionally,
- the
must be gre
and the
- ipsec_psk
key must
- be set. The in_key
, out_key
, and
- key
must not be
- set.
- ipsec_psk
- - Required key for GRE-over-IPsec interfaces. Specifies a
- pre-shared key for authentication that must be identical on
- both sides of the tunnel. Additionally, the
-
ipsec_local_ip
key must also be set.
-
+ there are none defined.
@@ -994,6 +1281,14 @@
for information on how this classifier works and how to configure it.
+
+ linux-hfsc
+ -
+ Linux "Hierarchical Fair Service Curve" classifier.
+ See
http://linux-ip.net/articles/hfsc.en/
for
+ information on how this classifier works.
+
+
@@ -1008,8 +1303,8 @@
Key-value pairs for configuring QoS features that depend on
.
- The linux-htb
class supports the following key-value
- pairs:
+ The linux-htb
and linux-hfsc
classes support
+ the following key-value pairs:
max-rate
- Maximum rate shared by all queued traffic, in bit/s.
@@ -1042,7 +1337,8 @@
column="type"/> of
min-rate
are:
min-rate
- - Minimum guaranteed bandwidth, in bit/s. Required.
+ - Minimum guaranteed bandwidth, in bit/s. Required. The
+ floor value is 1500 bytes/s (12,000 bit/s).
The key-value pairs defined for of linux-htb
are:
@@ -1067,6 +1363,17 @@
a queue with a larger value receives any. Specific priority
values are unimportant; only relative ordering matters.
+ The key-value pairs defined for of linux-hfsc
are:
+
+ min-rate
+ - Minimum guaranteed bandwidth, in bit/s. Required.
+ max-rate
+ - Maximum allowed bandwidth, in bit/s. Optional. If specified, the
+ queue's rate will not be allowed to exceed the specified value, even
+ if excess bandwidth is available. If unspecified, defaults to no
+ limit.
+
@@ -1078,6 +1385,98 @@
+
+
+ A attaches to an to
+ implement 802.1ag Connectivity Fault Management (CFM). CFM allows a
+ group of Maintenance Points (MPs) called a Maintenance Association (MA)
+ to detect connectivity problems with each other. MPs within a MA should
+ have complete and exclusive interconnectivity. This is verified by
+ occasionally broadcasting Continuity Check Messages (CCMs) at a
+ configurable transmission interval. A is
+ responsible for collecting data about other MPs in its MA and
+ broadcasting CCMs.
+
+
+
+
+ A Maintenance Point ID (MPID) uniquely identifies each endpoint within
+ a Maintenance Association (see ). The MPID is
+ used to identify this to other endpoints in the
+ MA.
+
+
+
+ A set of which this
+ should have connectivity to. If this
+ does not have connectivity to any MPs in this
+ set, or has connectivity to any MPs not in this set, a fault is
+ signaled.
+
+
+
+ A Maintenance Association (MA) name pairs with a Maintenance Domain
+ (MD) name to uniquely identify a MA. A MA is a group of endpoints who
+ have complete and exclusive interconnectivity. Defaults to
+ ovs
if unset.
+
+
+
+ A Maintenance Domain name pairs with a Maintenance Association name to
+ uniquely identify a MA. Defaults to ovs
if unset.
+
+
+
+ The transmission interval of CCMs in milliseconds. Three missed CCMs
+ indicate a connectivity fault. Defaults to 1000ms.
+
+
+
+
+
+ A set of MPIDs representing MPs to which this
+ has detected connectivity that are not in the
+ set. This should not
+ have connectivity to any MPs not listed in .
+ Thus, if this set is non-empty a fault is indicated.
+
+
+
+ A set of MAIDs representing foreign Maintenance Associations (MAs)
+ which this has detected connectivity to. A
+ should not have connectivity to a Maintenance
+ Association other than its own. Thus, if this set is non-empty a fault
+ is indicated.
+
+
+
+ Indicates a Connectivity Fault caused by a configuration error, a down
+ remote MP, or unexpected connectivity to a remote MAID or remote MP.
+
+
+
+
+
+
+ A represents a MP which a
+ has or should have connectivity to.
+
+
+
+
+ A Maintenance Point ID (MPID) uniquely identifies each endpoint within
+ a Maintenance Association. All MPs within a MA should have a unique
+ MPID.
+
+
+
+
+
+ Indicates a connectivity fault.
+
+
+
+
A port mirror within a .
A port mirror configures a bridge to send selected frames to special
@@ -1175,7 +1574,7 @@
Open vSwitch supports two kinds of OpenFlow controllers:
-
+
- Primary controllers
-
@@ -1445,6 +1844,199 @@
unique. No common key-value pairs are currently defined.
+
+
+
+
true
if currently connected to this controller,
+ false
otherwise.
+
+
+
+ The level of authority this controller has on the associated
+ bridge. Possible values are:
+
+ other
+ - Allows the controller access to all OpenFlow features.
+
+
+ master
+ - Equivalent to
other
, except that there may be at
+ most one master controller at a time. When a controller configures
+ itself as master
, any existing master is demoted to
+ the slave
role.
+
+
+ slave
+ - Allows the controller read-only access to OpenFlow features.
+ Attempts to modify the flow table will be rejected with an
+ error. Slave controllers do not receive OFPT_PACKET_IN or
+ OFPT_FLOW_REMOVED messages, but they do receive OFPT_PORT_STATUS
+ messages.
+
+
+
+
+ Key-value pairs that report controller status.
+
+ last_error
+ - A human-readable description of the last error on the connection
+ to the controller; i.e.
strerror(errno)
. This key
+ will exist only if an error has occurred.
+
+
+ state
+ - The state of the connection to the controller. Possible values
+ are:
VOID
, BACKOFF
,
+ CONNECTING
, ACTIVE
, and
+ IDLE
.
+
+
+ time_in_state
+ - Seconds since connecting to (if currently connected) or
+ disconnecting from (if currently disconnected) this
+ controller.
+
+
+
+
+
+
+
+ Configuration for a database connection to an Open vSwitch database
+ (OVSDB) client.
+
+
+
+ This table primarily configures the Open vSwitch database
+ (ovsdb-server
), not the Open vSwitch switch
+ (ovs-vswitchd
). The switch does read the table to determine
+ what connections should be treated as in-band.
+
+
+
+ The Open vSwitch database server can initiate and maintain active
+ connections to remote clients. It can also listen for database
+ connections.
+
+
+
+
+ Connection method for managers.
+
+ The following connection methods are currently supported:
+
+
+ ssl:ip
[:port
]
+ -
+
+ The specified SSL port (default: 6632) on the host at
+ the given ip, which must be expressed as an IP address
+ (not a DNS name). The
+ column in the table must point to a
+ valid SSL configuration when this form is used.
+
+
+ SSL support is an optional feature that is not always built as
+ part of Open vSwitch.
+
+
+
+ tcp:ip
[:port
]
+ -
+ The specified TCP port (default: 6632) on the host at
+ the given ip, which must be expressed as an IP address
+ (not a DNS name).
+
+ pssl:
[port][:ip
]
+ -
+
+ Listens for SSL connections on the specified TCP port
+ (default: 6632). If ip, which must be expressed as an
+ IP address (not a DNS name), is specified, then connections are
+ restricted to the specified local IP address.
+
+
+ The column in the table must point to a valid SSL
+ configuration when this form is used.
+
+
+ SSL support is an optional feature that is not always built as
+ part of Open vSwitch.
+
+
+ ptcp:
[port][:ip
]
+ -
+ Listens for connections on the specified TCP port
+ (default: 6632). If ip, which must be expressed as an
+ IP address (not a DNS name), is specified, then connections are
+ restricted to the specified local IP address.
+
+
+ When multiple managers are configured, the
+ values must be unique. Duplicate values yield
+ unspecified results.
+
+
+
+
+ If it is specified, this setting must be one of the following strings
+ that describes how Open vSwitch contacts this OVSDB client over the
+ network:
+
+
+
+ in-band
+ -
+ In this mode, this connection's traffic travels over a bridge
+ managed by Open vSwitch. With this setting, Open vSwitch allows
+ traffic to and from the client regardless of the contents of the
+ OpenFlow flow table. (Otherwise, Open vSwitch would never be able
+ to connect to the client, because it did not have a flow to enable
+ it.) This is the most common connection mode because it is not
+ necessary to maintain two independent networks.
+
+ out-of-band
+ -
+ In this mode, the client's traffic uses a control network separate
+ from that managed by Open vSwitch, that is, Open vSwitch does not
+ use any of its own network devices to communicate with the client.
+ The control network must be configured separately, before or after
+
ovs-vswitchd
is started.
+
+
+
+
+ If not specified, the default is implementation-specific.
+
+
+
+
+
+
+ Maximum number of milliseconds to wait between connection attempts.
+ Default is implementation-specific.
+
+
+
+ Maximum number of milliseconds of idle time on connection to the client
+ before sending an inactivity probe message. If Open vSwitch does not
+ communicate with the client for the specified number of seconds, it
+ will send a probe. If a response is not received for the same
+ additional amount of time, Open vSwitch assumes the connection has been
+ broken and attempts to reconnect. Default is implementation-specific.
+
+
+
+
+
+ Key-value pairs for use by external frameworks that integrate with Open
+ vSwitch, rather than by Open vSwitch itself. System integrators should
+ either use the Open vSwitch development mailing list to coordinate on
+ common key-value definitions, or choose key names that are likely to be
+ unique. No common key-value pairs are currently defined.
+
+