X-Git-Url: https://pintos-os.org/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=vswitchd%2Fvswitch.xml;h=6565b9582e6ab898b5b914ac9e679d6dcb599f73;hb=c97fb13280c565f55ed0de7cf0bf06ffe8320b70;hp=53c2650d17246bc8506a06d9b7995a27a14cb920;hpb=6333182946ffd368eb7623d7408185a521058b46;p=openvswitch diff --git a/vswitchd/vswitch.xml b/vswitchd/vswitch.xml index 53c2650d..6565b958 100644 --- a/vswitchd/vswitch.xml +++ b/vswitchd/vswitch.xml @@ -982,18 +982,77 @@ Configuration options whose interpretation varies based on . + + + +

+ Status information about interfaces attached to bridges, updated every + 5 seconds. Not all interfaces have all of these properties; virtual + interfaces don't have a link speed, for example. Non-applicable + columns will have empty values. +

+ +

+ The administrative state of the physical network link. +

+
+ + +

+ The observed state of the physical network link; + i.e. whether a carrier is detected by the interface. +

+
+ + +

+ The negotiated speed of the physical network link. + Valid values are positive integers greater than 0. +

+
+ + +

+ The duplex mode of the physical network link. +

+
+ + +

+ The MTU (maximum transmission unit); i.e. the largest + amount of data that can fit into a single Ethernet frame. + The standard Ethernet MTU is 1500 bytes. Some physical media + and many kinds of virtual interfaces can be configured with + higher MTUs. +

+

Key-value pairs that report port status. Supported status - values are type-dependent. + values are type-dependent; some interfaces may not have + a valid driver_name, for example.

The currently defined key-value pairs are:

+
+
driver_name
+
The name of the device driver controlling the network + adapter.
+
+
+
driver_version
+
The version string of the device driver controlling the + network adapter.
+
+
+
firmware_version
+
The version string of the network adapter's firmware, if + available.
+
source_ip
The source IP address used for an IPv4 tunnel end-point, - such as gre or capwap. Not - supported by all implementations.
+ such as gre or capwap.
tunnel_egress_iface
@@ -1003,6 +1062,12 @@ traffic destined for the configured remote_ip. This could be an internal interface such as a bridge port.
+
+
tunnel_egress_iface_carrier
+
Whether a carrier is detected on . Valid values are down + and up.
+
@@ -1779,6 +1844,60 @@ unique. No common key-value pairs are currently defined. + + + + true if currently connected to this controller, + false otherwise. + + + +

The level of authority this controller has on the associated + bridge. Possible values are:

+
+
other
+
Allows the controller access to all OpenFlow features.
+
+
+
master
+
Equivalent to other, except that there may be at + most one master controller at a time. When a controller configures + itself as master, any existing master is demoted to + the slaverole.
+
+
+
slave
+
Allows the controller read-only access to OpenFlow features. + Attempts to modify the flow table will be rejected with an + error. Slave controllers do not receive OFPT_PACKET_IN or + OFPT_FLOW_REMOVED messages, but they do receive OFPT_PORT_STATUS + messages.
+
+
+ + +

Key-value pairs that report controller status.

+
+
last_error
+
A human-readable description of the last error on the connection + to the controller; i.e. strerror(errno). This key + will exist only if an error has occurred.
+
+
+
state
+
The state of the connection to the controller. Possible values + are: VOID, BACKOFF, + CONNECTING, ACTIVE, and + IDLE.
+
+
+
time_in_state
+
Seconds since connecting to (if currently connected) or + disconnecting from (if currently disconnected) this + controller.
+
+
+