X-Git-Url: https://pintos-os.org/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=vswitchd%2Fvswitch.xml;h=328cf354c283c546f29c3943cdc806c6c5029a96;hb=54ae6fa8f1ae7401652d282609848605fc283104;hp=53c2650d17246bc8506a06d9b7995a27a14cb920;hpb=6333182946ffd368eb7623d7408185a521058b46;p=openvswitch
diff --git a/vswitchd/vswitch.xml b/vswitchd/vswitch.xml
index 53c2650d..328cf354 100644
--- a/vswitchd/vswitch.xml
+++ b/vswitchd/vswitch.xml
@@ -244,7 +244,7 @@
The version of the system identified by ,
- e.g.
System integrators are responsible for choosing and setting an
@@ -273,21 +273,6 @@
connection should be configured. See the table
for more information.
- Remote database clients to which the Open vSwitch's database server
- should connect or to which it should listen. Adding an OVSDB target
- to this set is equivalent to adding it to with all of the default options.
-
- Use of this column is deprecated and may be removed sometime in the
- future. New applications should use and set instead.
- A port that has more than one interface is a ``bonded port.'' Bonding
- allows for load balancing and fail-over. Open vSwitch supports
- ``source load balancing'' (SLB) and "active backup" bonding. SLB
- bonding assigns flows to slaves based on source MAC address and output
- VLAN, with periodic rebalancing as traffic patterns change. Active
- backup bonding assigns all flows to one slave, failing over to a backup
- slave when the active slave is disabled. Neither form of bonding
- require 802.3ad or other special support from the upstream switch to
- which the slave devices are connected.5.5.0-24648p
on XenServer 5.5.0 build 24648.
+ e.g. 5.6.100-39265p
on XenServer 5.6.100 build 39265.
balance-slb
active-backup
+ The following mode requires the upstream switch to support 802.3ad with
+ successful LACP negotiation. If LACP negotiation fails then
+ balance-slb
mode is used as a fallback:
+
balance-tcp
These columns apply only to bonded ports. Their values are otherwise ignored.
The type of bonding used for a bonded port. Currently supported
- values are balance-slb
and active-backup
.
- Defaults to SLB if unset.
The type of bonding used for a bonded port. Defaults to
+ balance-slb
if unset.
+
Configures LACP on this port. LACP allows directly connected
+ switches to negotiate which links may be bonded. LACP may be enabled
+ on non-bonded ports for the benefit of any switches they may be
+ connected to. active
ports are allowed to initiate LACP
+ negotiations. passive
ports are allowed to participate
+ in LACP negotiations initiated by a remote switch, but not allowed to
+ initiate such negotiations themselves. If unset Open vSwitch will
+ choose a reasonable default.
miimon
to detect failures. lacp-system-priority
+ Status information about interfaces attached to bridges, updated every + 5 seconds. Not all interfaces have all of these properties; virtual + interfaces don't have a link speed, for example. Non-applicable + columns will have empty values. +
++ The administrative state of the physical network link. +
++ The observed state of the physical network link; + i.e. whether a carrier is detected by the interface. +
++ The negotiated speed of the physical network link. + Valid values are positive integers greater than 0. +
++ The duplex mode of the physical network link. +
++ The MTU (maximum transmission unit); i.e. the largest + amount of data that can fit into a single Ethernet frame. + The standard Ethernet MTU is 1500 bytes. Some physical media + and many kinds of virtual interfaces can be configured with + higher MTUs. +
++ This column will be empty for an interface that does not + have an MTU as, for example, some kinds of tunnels do not. +
+
Key-value pairs that report port status. Supported status
- values are type
-dependent.
+ values are type
-dependent; some interfaces may not have
+ a valid driver_name
, for example.
The currently defined key-value pairs are:
+driver_name
driver_version
firmware_version
source_ip
gre
or capwap
. Not
- supported by all implementations.gre
or capwap
.
tunnel_egress_iface
remote_ip
.
This could be an internal interface such as a bridge port.
true
if currently connected to this controller,
+ false
otherwise.
+ The level of authority this controller has on the associated + bridge. Possible values are:
+other
master
other
, except that there may be at
+ most one master controller at a time. When a controller configures
+ itself as master
, any existing master is demoted to
+ the slave
role.slave
Key-value pairs that report controller status.
+last_error
strerror(errno)
. This key
+ will exist only if an error has occurred.state
VOID
, BACKOFF
,
+ CONNECTING
, ACTIVE
, and
+ IDLE
.time_in_state