X-Git-Url: https://pintos-os.org/cgi-bin/gitweb.cgi?a=blobdiff_plain;ds=sidebyside;f=vswitchd%2Fvswitch.xml;h=b74c55c8c7bea197cca76b13d36d82980befb687;hb=72c3b44800c5b25d5399b05e1bc6aece44414f49;hp=7b7a1ac928666a8399fa1e1d8bb84c872af204af;hpb=e58de0e38647f0ee62a8862e3565e5b788a03a7e;p=openvswitch
diff --git a/vswitchd/vswitch.xml b/vswitchd/vswitch.xml
index 7b7a1ac9..b74c55c8 100644
--- a/vswitchd/vswitch.xml
+++ b/vswitchd/vswitch.xml
@@ -1,15 +1,20 @@
A database with this schema holds the configuration for one Open
- vSwitch daemon. The root of the configuration for the daemon is
- the table, which must have exactly one
+
+ A database with this schema holds the configuration for one Open
+ vSwitch daemon. The top-level configuration for the daemon is the
+ table, which must have exactly one
record. Records in other tables are significant only when they
- can be reached directly or indirectly from the
- table.
A port that has more than one interface is a ``bonded port.'' - Bonding allows for load balancing and fail-over. Open vSwitch - supports ``source load balancing'' (SLB) bonding, which - assigns flows to slaves based on source MAC address and output VLAN, - with periodic rebalancing as traffic patterns change. This form of - bonding does not require 802.3ad or other special support from the - upstream switch to which the slave devices are connected.
+A port that has more than one interface is a ``bonded port.'' Bonding + allows for load balancing and fail-over. Some kinds of bonding will + work with any kind of upstream switch:
+ +balance-slb
active-backup
+ The following mode requires the upstream switch to support 802.3ad with
+ successful LACP negotiation. If LACP negotiation fails then
+ balance-slb
mode is used as a fallback:
+
balance-tcp
These columns apply only to bonded ports. Their values are otherwise ignored.
+The type of bonding used for a bonded port. Defaults to
+ balance-slb
if unset.
+
For a bonded port, the number of milliseconds for which carrier must stay up on an interface before the interface is considered to be up. @@ -485,6 +559,18 @@ name of the port. Use only for compatibility with legacy software that requires this.
Configures LACP on this port. LACP allows directly connected
+ switches to negotiate which links may be bonded. LACP may be enabled
+ on non-bonded ports for the benefit of any switches they may be
+ connected to. active
ports are allowed to initiate LACP
+ negotiations. passive
ports are allowed to participate
+ in LACP negotiations initiated by a remote switch, but not allowed to
+ initiate such negotiations themselves. If unset Open vSwitch will
+ choose a reasonable default.
xx:xx:xx:xx:xx:xx
.bond-rebalance-interval
bond-detect-mode
carrier
and miimon
. Defaults
+ to carrier
which uses each interface's carrier to detect
+ failures. When set to miimon
, will check for failures
+ by polling each interface's MII. bond-miimon-interval
miimon
to detect failures. lacp-system-priority
lacp-time
fast
and
+ slow
. By default slow
is used. When
+ configured to be fast
more frequent LACP heartbeats
+ will be requested causing connectivity problems to be detected more
+ quickly.false
to disable. If IPsec is enabled through the
- parameters, header caching will be
- automatically disabled.
+ false
to disable.
+
+
+ ipsec_gre
gre
) must be uniquely identified by the
+ combination of remote_ip
and
+ local_ip
. Note that if two ports are defined
+ that are the same except one has an optional identifier and
+ the other does not, the more specific one is matched first.
+ An authentication method of peer_cert
or
+ psk
must be defined. The following options may
+ be specified in the column:
+ remote_ip
local_ip
peer_cert
certificate
option.certificate
private_key
certificate
. If certificate
+ contains the private key, this option may be omitted.psk
in_key
flow
. If
+ flow
is specified then any key will be accepted
+ and the key will be placed in the tun_id
field
+ for matching in the flow table. The ovs-ofctl manual page
+ contains additional information about matching fields in
+ OpenFlow flows. Default is no key.out_key
flow
. If
+ flow
is specified then the key may be set using
+ the set_tunnel
Nicira OpenFlow vendor extension (0
+ is used in the absence of an action). The ovs-ofctl manual
+ page contains additional information about the Nicira OpenFlow
+ vendor extensions. Default is no key.key
in_key
and
+ out_key
at the same time.tos
inherit
, in which case the ToS will be copied from
+ the inner packet if it is IPv4 or IPv6 (otherwise it will be
+ 0). Note that the ECN fields are always inherited. Default is
+ 0.ttl
inherit
, in which case the
+ TTL will be copied from the inner packet if it is IPv4 or IPv6
+ (otherwise it will be the system default, typically 64).
+ Default is the system default TTL.csum
true
to enable.pmtud
false
to disable.capwap
remote_ip
and
local_ip
. If two ports are defined that are the same
except one includes local_ip
and the other does not,
@@ -798,18 +1019,97 @@
Configuration options whose interpretation varies based on
.
+
+
+ + Status information about interfaces attached to bridges, updated every + 5 seconds. Not all interfaces have all of these properties; virtual + interfaces don't have a link speed, for example. Non-applicable + columns will have empty values. +
++ The administrative state of the physical network link. +
++ The observed state of the physical network link. This is ordinarily + the link's carrier status. If the interface's is + a bond configured for miimon monitoring, it is instead the network + link's miimon status. +
++ The negotiated speed of the physical network link. + Valid values are positive integers greater than 0. +
++ The duplex mode of the physical network link. +
++ The MTU (maximum transmission unit); i.e. the largest + amount of data that can fit into a single Ethernet frame. + The standard Ethernet MTU is 1500 bytes. Some physical media + and many kinds of virtual interfaces can be configured with + higher MTUs. +
++ This column will be empty for an interface that does not + have an MTU as, for example, some kinds of tunnels do not. +
+
Key-value pairs that report port status. Supported status
- values are type
-dependent.
+ values are type
-dependent; some interfaces may not have
+ a valid driver_name
, for example.
The only currently defined key-value pair is:
+The currently defined key-value pairs are:
+driver_name
driver_version
firmware_version
source_ip
gre
or capwap
. Not
- supported by all implementations.gre
or capwap
.
+ tunnel_egress_iface
remote_ip
.
+ This could be an internal interface such as a bridge port.openvswitch-ipsec
package for
- Debian. The currently defined key-value pairs are:
+ Key-value pairs for rarely used interface features.
ipsec_local_ip
gre
and the
- ipsec_psk
key must
- be set. The in_key
, out_key
, and
- key
must not be
- set.ipsec_psk
ipsec_local_ip
key must also be set.lacp-port-priority
linux-htb
are:
min-rate
max-rate
linux-hfsc
are:
min-rate
max-rate
discover
Enables controller discovery.
-In controller discovery mode, Open vSwitch broadcasts a DHCP
- request with vendor class identifier OpenFlow
across
- all of the bridge's network devices. It will accept any valid
- DHCP reply that has the same vendor class identifier and includes
- a vendor-specific option with code 1 whose contents are a string
- specifying the location of the controller in the same format as
- .
The DHCP reply may also, optionally, include a vendor-specific
- option with code 2 whose contents are a string specifying the URI
- to the base of the OpenFlow PKI
- (e.g. http://192.168.0.1/openflow/pki
). This URI is
- used only for bootstrapping the OpenFlow PKI at initial switch
- setup; ovs-vswitchd
does not use it at all.
The following connection methods are currently supported for service @@ -1487,10 +1744,7 @@
If not specified, the default is implementation-specific. If
- is discover
, the connection mode
- is always treated as in-band
regardless of the actual
- setting.
If not specified, the default is implementation-specific.
@@ -1540,33 +1794,9 @@ -These values are considered only when
- is discover
.
^
. If not specified, the default
- is implementation-specific.
- /etc/resolv.conf
when the
- controller is discovered. If not specified, the default
- is implementation-specific. Open vSwitch will only modify
- /etc/resolv.conf
if the DHCP response that it receives
- specifies one or more DNS servers.
- These values are considered only in in-band control mode (see
- ) and only when
- is not discover
. (For controller discovery, the network
- configuration obtained via DHCP is used instead.)
When multiple controllers are configured on a single bridge, there should be only one set of unique values in these columns. If different @@ -1603,6 +1833,60 @@ unique. No common key-value pairs are currently defined.
true
if currently connected to this controller,
+ false
otherwise.
+ The level of authority this controller has on the associated + bridge. Possible values are:
+other
master
other
, except that there may be at
+ most one master controller at a time. When a controller configures
+ itself as master
, any existing master is demoted to
+ the slave
role.slave
Key-value pairs that report controller status.
+last_error
strerror(errno)
. This key
+ will exist only if an error has occurred.state
VOID
(connection is disabled),
+ BACKOFF
(attempting to reconnect at an increasing
+ period), CONNECTING
(attempting to connect),
+ ACTIVE
(connected, remote host responsive), and
+ IDLE
(remote host idle, sending keep-alive). These
+ values may change in the future. They are provided only for human
+ consumption.sec_since_connect
sec_since_disconnect