X-Git-Url: https://pintos-os.org/cgi-bin/gitweb.cgi?a=blobdiff_plain;ds=inline;f=vswitchd%2Fvswitch.xml;h=e9ea0c4c73a2d1e79eeaf946fa618c932daba3c4;hb=4206b80f6444ceef47ceb9e1a6b88a40eabacb1f;hp=b9b7b97aee646ef1bc3c110d604daac79c6b5c41;hpb=612ca9c5d7e1f042d4b7b24d046832cad559124b;p=openvswitch diff --git a/vswitchd/vswitch.xml b/vswitchd/vswitch.xml index b9b7b97a..e9ea0c4c 100644 --- a/vswitchd/vswitch.xml +++ b/vswitchd/vswitch.xml @@ -409,7 +409,16 @@ any defined controllers forever.
-If this value is unset, the default is implementation-specific.
+
+ The default is standalone
if the value is unset, but
+ future versions of Open vSwitch may change the default.
+
+ The standalone
mode can create forwarding loops on a
+ bridge that has more than one uplink port unless STP is enabled. To
+ avoid loops on such a bridge, configure secure
mode or
+ enable STP (see ).
+
When more than one controller is configured, is considered only when none of the configured controllers can be contacted.
@@ -547,6 +556,46 @@ and if Open vSwitch node does not run STP, then this option should be enabled. Default is disabled, set totrue
to enable.
+
+ The following destination MAC addresss will not be forwarded when this
+ option is enabled.
+ 01:80:c2:00:00:00
01:80:c2:00:00:01
01:80:c2:00:00:0x
00:e0:2b:00:00:00
00:e0:2b:00:00:04
and 00:e0:2b:00:00:06
+ 01:00:0c:cc:cc:cc
01:00:0c:cc:cc:cd
01:00:0c:cd:cd:cd
01:00:0c:00:00:00
01:00:0c:cc:cc:cx
A port that has more than one interface is a ``bonded port.'' Bonding - allows for load balancing and fail-over. Some kinds of bonding will - work with any kind of upstream switch:
+ allows for load balancing and fail-over. + ++ The following types of bonding will work with any kind of upstream + switch. On the upstream switch, do not configure the interfaces as a + bond: +
balance-slb
active-backup
stable
Deprecated and slated for removal in February 2013.
Attempts to always assign a given flow to the same slave
consistently. In an effort to maintain stability, no load
balancing is done. Uses a similar hashing strategy to
@@ -841,7 +897,7 @@
- The number of milliseconds for which carrier must stay up on an
+ The number of milliseconds for which the link must stay up on an
interface before the interface is considered to be up. Specify
0
to enable the interface immediately.
0
to disable the interface immediately.
These settings control behavior when a bond is in
- balance-slb
mode, regardless of whether the bond was
- intentionally configured in SLB mode or it fell back to SLB mode
- because LACP negotiation failed.
+ balance-slb
or balance-tcp
mode.
gre64
ipsec_gre64
capwap
null
These options apply to interfaces with of
- gre
, ipsec_gre
, and capwap
.
+ gre
, ipsec_gre
, gre64
,
+ ipsec_gre64
, and capwap
.
@@ -1258,7 +1329,8 @@
inherit
, in which case
+ packet. ToS is interpreted as DSCP and ECN bits, ECN part must be
+ zero. It may also be the word inherit
, in which case
the ToS will be copied from the inner packet if it is IPv4 or IPv6
(otherwise it will be 0). The ECN fields are always inherited.
Default is 0.
@@ -1646,6 +1718,12 @@
faulted otherwise.
+ When operating over tunnels which have no in_key
, or an
+ in_key
of flow
. CFM will only accept CCMs
+ with a tunnel key of zero.
+
When in extended mode, indicates the operational state of the
+ remote endpoint as either up
or down
. See
+ .
+
The eviction process only considers flows that have an idle timeout or a hard timeout. That is, eviction never deletes permanent flows. - (Permanent flows do count against . + (Permanent flows do count against .)
@@ -2305,36 +2385,12 @@ sent out an implicit VLAN port, the frame will not be tagged. This type of mirroring is sometimes called RSPAN.
- The following destination MAC addresses will not be mirrored to a - VLAN to avoid confusing switches that interpret the protocols that - they represent: + See the documentation for + in the + table for a list of destination MAC + addresses which will not be mirrored to a VLAN to avoid confusing + switches that interpret the protocols that they represent.
-01:80:c2:00:00:00
01:80:c2:00:00:01
01:80:c2:00:00:0x
01:00:0c:cc:cc:cc
01:00:0c:cc:cc:cd
01:00:0c:cd:cd:cd
01:00:0c:00:00:00
Please note: Mirroring to a VLAN can disrupt a network that contains unmanaged switches. Consider an unmanaged physical switch with two ports: port 1, connected to an end host, and port 2, @@ -2725,10 +2781,9 @@ Service (QoS) on IP networks. The DSCP value specified here is used when establishing the connection - between the controller and the Open vSwitch. The connection must be - reset for the new DSCP values to take effect. If no value is - specified, a default value of 48 is chosen. Valid DSCP values must be - in the range 0 to 63. + between the controller and the Open vSwitch. If no value is specified, + a default value of 48 is chosen. Valid DSCP values must be in the + range 0 to 63.