ofproto: Group struct cfm forward declaration with the rest of them.

[openvswitch] / vswitchd / vswitch.xml

diff --git a/vswitchd/vswitch.xml b/vswitchd/vswitch.xml
index 6031b5a0efcafe7c7938afd15abf0f24bb0804b0..4cdc1b1ca38da4b38b94b63d5fe3e71681b74ba7 100644 (file)
--- a/vswitchd/vswitch.xml
+++ b/vswitchd/vswitch.xml
@@ -647,18 +647,33 @@
           <dd> The number of milliseconds between successive attempts to
             poll each interface's MII.  Only relevant on ports which use
             <code>miimon</code> to detect failures. </dd>
+          <dt><code>lacp-system-id</code></dt>
+          <dd> The LACP system ID of this <ref table="Port"/>.  The system ID
+            of a LACP bond is used to identify itself to its partners.  Must
+            be a nonzero MAC address.</dd>
           <dt><code>lacp-system-priority</code></dt>
           <dd> The LACP system priority of this <ref table="Port"/>.  In
             LACP negotiations, link status decisions are made by the system
             with the numerically lower priority.  Must be a number between 1
             and 65535.</dd>
           <dt><code>lacp-time</code></dt>
-          <dd> The LACP timing which should be used on this
-            <ref table="Port"/>.  Possible values are <code>fast</code> and
-            <code>slow</code>.  By default <code>slow</code> is used.  When
-            configured to be <code>fast</code> more frequent LACP heartbeats
-            will be requested causing connectivity problems to be detected more
-            quickly.</dd>
+          <dd>
+            <p>The LACP timing which should be used on this
+              <ref table="Port"/>.  Possible values are <code>fast</code>,
+              <code>slow</code> and a positive number of milliseconds.  By
+              default <code>slow</code> is used.  When configured to be
+              <code>fast</code> LACP heartbeats are requested at a rate of once
+              per second causing connectivity problems to be detected more
+              quickly.  In <code>slow</code> mode, heartbeats are requested at
+              a rate of once every 30 seconds.</p>
+
+            <p>Users may manually set a heartbeat transmission rate to increase
+              the fault detection speed further.  When manually set, OVS
+              expects the partner switch to be configured with the same
+              transmission rate.  Manually setting <code>lacp-time</code> to
+              something other than <code>fast</code> or <code>slow</code> is
+              not supported by the LACP specification.</p>
+          </dd>
           <dt><code>lacp-strict</code></dt>
           <dd> When <code>true</code>, configures this <ref table="Port"/> to
             require successful LACP negotiations to enable any slaves.
@@ -1266,6 +1281,11 @@
       <column name="other_config">
         Key-value pairs for rarely used interface features.
         <dl>
+          <dt><code>lacp-port-id</code></dt>
+          <dd> The LACP port ID of this <ref table="Interface"/>.  Port IDs are
+            used in LACP negotiations to identify individual ports
+            participating in a bond.  Must be a number between 1 and
+            65535.</dd>
           <dt><code>lacp-port-priority</code></dt>
           <dd> The LACP port priority of this <ref table="Interface"/>.  In
             LACP negotiations <ref table="Interface"/>s with numerically lower