the same except one has an optional identifier and the other does
not, the more specific one is matched first. <code>in_key</code>
is considered more specific than <code>local_ip</code> if a port
- defines one and another port defines the other. The arguments
- are:
+ defines one and another port defines the other. The following
+ options may be specified in the <ref column="options"/> column:
<dl>
<dt><code>remote_ip</code></dt>
<dd>Required. The tunnel endpoint.</dd>
</dl>
</dd>
<dt><code>patch</code></dt>
- <dd>A pair of virtual devices that act as a patch cable. A
- <code>peer</code> argument is required that indicates the name
- of the other side of the patch. Since a patch must work in
- pairs, a second patch interface must be declared with the
- <code>name</code> and <code>peer</code> arguments reversed.</dd>
+ <dd>
+ <p>
+ A pair of virtual devices that act as a patch cable. The <ref
+ column="options"/> column must have the following key-value pair:
+ </p>
+ <dl>
+ <dt><code>peer</code></dt>
+ <dd>
+ The <ref column="name"/> of the <ref table="Interface"/> for
+ the other side of the patch. The named <ref
+ table="Interface"/>'s own <code>peer</code> option must specify
+ this <ref table="Interface"/>'s name. That is, the two patch
+ interfaces must have reversed <ref column="name"/> and
+ <code>peer</code> values.
+ </dd>
+ </dl>
+ </dd>
</dl>
</column>
<table name="Controller" title="OpenFlow controller configuration.">
<p>An OpenFlow controller.</p>
- <p>Open vSwitch permits a bridge to have any number of OpenFlow
- controllers. When multiple controllers are configured, Open vSwitch
- connects to all of them simultaneously. OpenFlow 1.0 does not specify
- how multiple controllers coordinate in interacting with a single switch,
- so more than one controller should be specified only if the controllers
- are themselves designed to coordinate with each other.</p>
+ <p>
+ Open vSwitch supports two kinds of OpenFlow controllers:
+ </p>
+
+ <dl>
+ <dt>Primary controllers</dt>
+ <dd>
+ <p>
+ This is the kind of controller envisioned by the OpenFlow 1.0
+ specification. Usually, a primary controller implements a network
+ policy by taking charge of the switch's flow table.
+ </p>
+
+ <p>
+ Open vSwitch initiates and maintains persistent connections to
+ primary controllers, retrying the connection each time it fails or
+ drops. The <ref table="Bridge" column="fail_mode"/> column in the
+ <ref table="Bridge"/> table applies to primary controllers.
+ </p>
+
+ <p>
+ Open vSwitch permits a bridge to have any number of primary
+ controllers. When multiple controllers are configured, Open
+ vSwitch connects to all of them simultaneously. Because
+ OpenFlow 1.0 does not specify how multiple controllers
+ coordinate in interacting with a single switch, more than
+ one primary controller should be specified only if the
+ controllers are themselves designed to coordinate with each
+ other. (The Nicira-defined <code>NXT_ROLE</code> OpenFlow
+ vendor extension may be useful for this.)
+ </p>
+ </dd>
+ <dt>Service controllers</dt>
+ <dd>
+ <p>
+ These kinds of OpenFlow controller connections are intended for
+ occasional support and maintenance use, e.g. with
+ <code>ovs-ofctl</code>. Usually a service controller connects only
+ briefly to inspect or modify some of a switch's state.
+ </p>
+
+ <p>
+ Open vSwitch listens for incoming connections from service
+ controllers. The service controllers initiate and, if necessary,
+ maintain the connections from their end. The <ref table="Bridge"
+ column="fail_mode"/> column in the <ref table="Bridge"/> table does
+ not apply to service controllers.
+ </p>
+
+ <p>
+ Open vSwitch supports configuring any number of service controllers.
+ </p>
+ </dd>
+ </dl>
+
+ <p>
+ The <ref column="target"/> determines the type of controller.
+ </p>
<group title="Core Features">
<column name="target">
- <p>Connection method for controller.
- The following connection methods are currently
- supported:</p>
+ <p>Connection method for controller.</p>
+ <p>
+ The following connection methods are currently supported for primary
+ controllers:
+ </p>
<dl>
<dt><code>ssl:<var>ip</var></code>[<code>:<var>port</var></code>]</dt>
<dd>
<p>The specified SSL <var>port</var> (default: 6633) on the host at
- the given <var>ip</var>, which must be expressed as an IP address
- (not a DNS name). The <ref table="Open_vSwitch" column="ssl"/>
- column in the <ref table="Open_vSwitch"/> must point to a valid
- SSL configuration when this form is used.</p>
+ the given <var>ip</var>, which must be expressed as an IP address
+ (not a DNS name). The <ref table="Open_vSwitch" column="ssl"/>
+ column in the <ref table="Open_vSwitch"/> table must point to a
+ valid SSL configuration when this form is used.</p>
<p>SSL support is an optional feature that is not always built as
part of Open vSwitch.</p>
</dd>
used only for bootstrapping the OpenFlow PKI at initial switch
setup; <code>ovs-vswitchd</code> does not use it at all.</p>
</dd>
- <dt><code>none</code></dt>
- <dd>Disables the controller.</dd>
+ </dl>
+ <p>
+ The following connection methods are currently supported for service
+ controllers:
+ </p>
+ <dl>
+ <dt><code>pssl:</code>[<var>port</var>][<code>:<var>ip</var></code>]</dt>
+ <dd>
+ <p>
+ Listens for SSL connections on the specified TCP <var>port</var>
+ (default: 6633). If <var>ip</var>, which must be expressed as an
+ IP address (not a DNS name), is specified, then connections are
+ restricted to the specified local IP address.
+ </p>
+ <p>
+ The <ref table="Open_vSwitch" column="ssl"/> column in the <ref
+ table="Open_vSwitch"/> table must point to a valid SSL
+ configuration when this form is used.
+ </p>
+ <p>SSL support is an optional feature that is not always built as
+ part of Open vSwitch.</p>
+ </dd>
+ <dt><code>ptcp:</code>[<var>port</var>][<code>:<var>ip</var></code>]</dt>
+ <dd>
+ Listens for connections on the specified TCP <var>port</var>
+ (default: 6633). If <var>ip</var>, which must be expressed as an
+ IP address (not a DNS name), is specified, then connections are
+ restricted to the specified local IP address.
+ </dd>
</dl>
<p>When multiple controllers are configured for a single bridge, the
<ref column="target"/> values must be unique. Duplicate
projects / openvswitch / blobdiff