included, then its MAC address is by default the lowest-numbered MAC
address among the other bridge ports, ignoring other internal ports
and bridge ports that are
-used as port mirroring destinations (see \fBPort Mirroring\fR, below). To
-use a specific MAC address instead, set \fBbridge.\fIname\fB.mac\fR to
-a MAC address in the format
+used as port mirroring destinations (see \fBPort Mirroring\fR, below).
+For this purpose, the MAC of a bonded port (see \fBNetwork Device
+Bonding\fR, below) is by default the MAC of its slave whose name is first in
+alphabetical order.
+There are two ways to modify this algorithm for selecting the MAC
+address of the local port:
+.IP \(bu
+To use a specific MAC address for the local port, set
+\fBbridge.\fIname\fB.mac\fR to a MAC address in the format
\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR, where each
-\fIx\fR is a hex digit. If no valid MAC address can be determined
+\fIx\fR is a hex digit.
+.IP \(bu
+To override the MAC of a port for the purpose of this algorithm, set
+\fBport.\fIport\fB.mac\fR to a MAC address in the format described
+above.
+.PP
+If no valid MAC address can be determined
either of these ways, then a MAC address is randomly generated.
.PP
The following syntax defines a bridge named \fBmybr\fR, configured
IP flows, such as the principals involved and duration. A bridge may be
configured to send NetFlow v5 records to NetFlow collectors when flows
end. To enable, define the key \fBnetflow.\fIbridge\fB.host\fR for each
-collector in the form \fIhost\fB:\fIport\fR. Records from \fIbridge\fR
-will be sent to each \fIhost\fR on UDP \fIport\fR.
+collector in the form \fIip\fB:\fIport\fR. Records from \fIbridge\fR
+will be sent to each \fIip\fR on UDP \fIport\fR. The \fIip\fR must
+be specified numerically, not as a DNS name.
The NetFlow messages will use the datapath index for the engine type and id.
This can be overridden with the \fBnetflow.\fIbridge\fB.engine-type\fR and
functionality is enabled by setting the key \fBmgmt.controller\fR to one
of the following values:
.
-.TP
-\fBssl:\fIhost\fR[\fB:\fIport\fR]
-The specified SSL \fIport\fR (default: 6633) on the given remote
-\fIhost\fR. SSL must be configured when this form is used (see \fBSSL
+.IP "\fBssl:\fIip\fR[\fB:\fIport\fR]"
+The specified SSL \fIport\fR (default: 6633) on the host at the given
+\fIip\fR, which must be expressed as an IP address (not a DNS name).
+SSL must be configured when this form is used (see \fBSSL
Configuration\fR, below).
.
-.TP
-\fBtcp:\fIhost\fR[\fB:\fIport\fR]
-The specified TCP \fIport\fR (default: 6633) on the given remote
-\fIhost\fR.
+.IP "\fBtcp:\fIip\fR[\fB:\fIport\fR]"
+The specified TCP \fIport\fR (default: 6633) on the host at the given
+\fIip\fR, which must be expressed as an IP address (not a DNS name).
.PP
The maximum time between attempts to connect to the controller may be
specified in integral seconds with the \fBmgmt.max-backoff\fR key. The
-default maximum backoff is 15 seconds, and the minimum value is 1
+default maximum backoff is 8 seconds, and the minimum value is 1
second.
An inactivity probe may be configured with the \fBmgmt.inactivity-probe\fR
specified number of seconds, it will send a probe. If a response is not
received for an additional amount of that time, \fBovs\-vswitchd\fR assumes
the connection has been broken and attempts to reconnect. The default
-is 15 seconds, and the minimum value is 5 seconds.
+and minimum values are both 5 seconds.
A management id may be specified with the \fBmgmt.id\fR key. It takes
an id in the form of exactly 12 hexadecimal digits. If one is not
.RE
.
.TP
-\fBssl:\fIhost\fR[\fB:\fIport\fR]
-The specified SSL \fIport\fR (default: 6633) on the given remote
-\fIhost\fR. SSL must be configured when this form is used (see \fBSSL
+\fBssl:\fIip\fR[\fB:\fIport\fR]
+The specified SSL \fIport\fR (default: 6633) on the host at the given
+\fIip\fR, which must be expressed as an IP address (not a DNS name).
+SSL must be configured when this form is used (see \fBSSL
Configuration\fR, below).
.
.TP
-\fBtcp:\fIhost\fR[\fB:\fIport\fR]
-The specified TCP \fIport\fR (default: 6633) on the given remote
-\fIhost\fR.
+\fBtcp:\fIip\fR[\fB:\fIport\fR]
+The specified TCP \fIport\fR (default: 6633) on the host at the given
+\fIip\fR, which must be expressed as an IP address (not a DNS name).
.
.TP
\fBunix:\fIfile\fR