.SS "Bridge Configuration"
A bridge (switch) with a given \fIname\fR is configured by specifying
the names of its network devices as values for key
-\fBbridge.\fIname\fB.port\fR. (The specified \fIname\fR may not begin
-with \fBdp\fR followed by a digit.)
+\fBbridge.\fIname\fB.port\fR.
.PP
The names given on \fBbridge.\fIname\fB.port\fR must be the names of
existing network devices, except for ``internal ports.'' An internal
included, then its MAC address is by default the lowest-numbered MAC
address among the other bridge ports, ignoring other internal ports
and bridge ports that are
-used as port mirroring destinations (see \fBPort Mirroring\fR, below). To
-use a specific MAC address instead, set \fBbridge.\fIname\fB.mac\fR to
-a MAC address in the format
+used as port mirroring destinations (see \fBPort Mirroring\fR, below).
+For this purpose, the MAC of a bonded port (see \fBNetwork Device
+Bonding\fR, below) is by default the MAC of its slave whose name is first in
+alphabetical order.
+There are two ways to modify this algorithm for selecting the MAC
+address of the local port:
+.IP \(bu
+To use a specific MAC address for the local port, set
+\fBbridge.\fIname\fB.mac\fR to a MAC address in the format
\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR, where each
-\fIx\fR is a hex digit. If no valid MAC address can be determined
+\fIx\fR is a hex digit.
+.IP \(bu
+To override the MAC of a port for the purpose of this algorithm, set
+\fBport.\fIport\fB.mac\fR to a MAC address in the format described
+above.
+.PP
+If no valid MAC address can be determined
either of these ways, then a MAC address is randomly generated.
.PP
The following syntax defines a bridge named \fBmybr\fR, configured
\fBbonding.\fIname\fB.updelay\fR or
\fBbonding.\fIname\fB.downdelay\fR, respectively, to a positive
integer, interpreted in milliseconds.
+The \fBupdelay\fR setting is honored only when at least one bonded
+interface is already enabled. When no interfaces are enabled, then
+the first bond interface to come up is enabled immediately. The
+\fBdowndelay\fR setting is always honored.
.PP
The following syntax bonds \fBeth0\fR and \fBeth1\fR into a bonding
device named \fBbond0\fR, which is added to bridge \fBmybr\fR along
any existing tag; when it is sent out an implicit VLAN port, the frame
will not be tagged. This type of mirroring may be referred to as
RSPAN.
+.IP
+Please note that mirroring to a VLAN can disrupt a network that
+contains unmanaged switches. Consider an unmanaged physical switch
+with two ports: port 1, connected to an end host, and port 2,
+connected to an Open vSwitch configured to mirror received packets
+into VLAN 123 on port 2. Suppose that the end host sends a packet on
+port 1 that the physical switch forwards to port 2. The Open vSwitch
+forwards this packet to its destination and then reflects it back on
+port 2 in VLAN 123. This reflected packet causes the unmanaged
+physical switch to replace the MAC learning table entry, which
+correctly pointed to port 1, with one that incorrectly points to port
+2. Afterward, the physical switch will direct packets destined for
+the end host to the Open vSwitch on port 2, instead of to the end host
+on port 1, disrupting connectivity. If mirroring to a VLAN is desired
+in this scenario, then the physical switch must be replaced by one
+that learns Ethernet addresses on a per-VLAN basis.
.ST "Example"
The following \fBovs\-vswitchd\fR configuration copies all frames received
on \fBeth1\fR or \fBeth2\fR to \fBeth3\fR.
IP flows, such as the principals involved and duration. A bridge may be
configured to send NetFlow v5 records to NetFlow collectors when flows
end. To enable, define the key \fBnetflow.\fIbridge\fB.host\fR for each
-collector in the form \fIhost\fB:\fIport\fR. Records from \fIbridge\fR
-will be sent to each \fIhost\fR on UDP \fIport\fR.
+collector in the form \fIip\fB:\fIport\fR. Records from \fIbridge\fR
+will be sent to each \fIip\fR on UDP \fIport\fR. The \fIip\fR must
+be specified numerically, not as a DNS name.
The NetFlow messages will use the datapath index for the engine type and id.
This can be overridden with the \fBnetflow.\fIbridge\fB.engine-type\fR and
functionality is enabled by setting the key \fBmgmt.controller\fR to one
of the following values:
.
-.TP
-\fBssl:\fIhost\fR[\fB:\fIport\fR]
-The specified SSL \fIport\fR (default: 6633) on the given remote
-\fIhost\fR. SSL must be configured when this form is used (see \fBSSL
+.IP "\fBssl:\fIip\fR[\fB:\fIport\fR]"
+The specified SSL \fIport\fR (default: 6633) on the host at the given
+\fIip\fR, which must be expressed as an IP address (not a DNS name).
+SSL must be configured when this form is used (see \fBSSL
Configuration\fR, below).
.
-.TP
-\fBtcp:\fIhost\fR[\fB:\fIport\fR]
-The specified TCP \fIport\fR (default: 6633) on the given remote
-\fIhost\fR.
+.IP "\fBtcp:\fIip\fR[\fB:\fIport\fR]"
+The specified TCP \fIport\fR (default: 6633) on the host at the given
+\fIip\fR, which must be expressed as an IP address (not a DNS name).
.PP
The maximum time between attempts to connect to the controller may be
specified in integral seconds with the \fBmgmt.max-backoff\fR key. The
-default maximum backoff is 15 seconds, and the minimum value is 1
+default maximum backoff is 8 seconds, and the minimum value is 1
second.
An inactivity probe may be configured with the \fBmgmt.inactivity-probe\fR
specified number of seconds, it will send a probe. If a response is not
received for an additional amount of that time, \fBovs\-vswitchd\fR assumes
the connection has been broken and attempts to reconnect. The default
-is 15 seconds, and the minimum value is 5 seconds.
+and minimum values are both 5 seconds.
A management id may be specified with the \fBmgmt.id\fR key. It takes
an id in the form of exactly 12 hexadecimal digits. If one is not
.TP
\fBdiscover\fR
Use controller discovery to find the local OpenFlow controller.
-Refer to \fBsecchan\fR(8) for information on how to configure a DHCP
+Refer to \fB\ovs\-openflowd\fR(8) for information on how to configure a DHCP
server to support controller discovery. The following additional
options control the discovery process:
.
.RE
.
.TP
-\fBssl:\fIhost\fR[\fB:\fIport\fR]
-The specified SSL \fIport\fR (default: 6633) on the given remote
-\fIhost\fR. SSL must be configured when this form is used (see \fBSSL
+\fBssl:\fIip\fR[\fB:\fIport\fR]
+The specified SSL \fIport\fR (default: 6633) on the host at the given
+\fIip\fR, which must be expressed as an IP address (not a DNS name).
+SSL must be configured when this form is used (see \fBSSL
Configuration\fR, below).
.
.TP
-\fBtcp:\fIhost\fR[\fB:\fIport\fR]
-The specified TCP \fIport\fR (default: 6633) on the given remote
-\fIhost\fR.
+\fBtcp:\fIip\fR[\fB:\fIport\fR]
+The specified TCP \fIport\fR (default: 6633) on the host at the given
+\fIip\fR, which must be expressed as an IP address (not a DNS name).
.
.TP
\fBunix:\fIfile\fR
By default, or if this is set to \fBtrue\fR, \fBovs\-vswitchd\fR connects
to the controller in-band. If this is set to \fBfalse\fR,
\fBovs\-vswitchd\fR connects to the controller out-of-band. Refer to
-\fBsecchan\fR(8) for a description of in-band and out-of-band control.
+\fBovs\-openflowd\fR(8) for a description of in-band and out-of-band control.
.IP "\fBbridge.\fIname\fB.controller.ip=\fIip\fR"
If specified, the IP address to configure on the bridge's local port.
.IP "\fBbridge.\fIname\fB.controller.netmask=\fInetmask\fR"
message to be received from the controller for \fIsecs\fR seconds
before it sends a inactivity probe to the controller. After sending
the inactivity probe, if no response is received for an additional
-\fIsecs\fR seconds, the secure channel assumes that the connection has
+\fIsecs\fR seconds, \fBovs-vswitchd\fR assumes that the connection has
been broken and attempts to reconnect.
.IP
Changing the inactivity probe interval also changes the interval