openflow: Fix frag config flag values

[openvswitch] / utilities / ovs-openflowd.8.in

diff --git a/utilities/ovs-openflowd.8.in b/utilities/ovs-openflowd.8.in
index 2441279ed9a821c0ddf453d30ff2d75849ff57c2..b98e07d2603757fb3d869aab14a68a0314e64bf2 100644 (file)
--- a/utilities/ovs-openflowd.8.in
+++ b/utilities/ovs-openflowd.8.in
@@ -155,6 +155,53 @@ the local port network device, and start the DHCP client afterward.
 .RE
 
 .SH OPTIONS
+.SS "OpenFlow Options"
+.TP
+\fB--datapath-id=\fIdpid\fR
+Sets \fIdpid\fR, which must consist of exactly 16 hexadecimal digits,
+as the datapath ID that the switch will use to identify itself to the
+OpenFlow controller.
+
+If this option is omitted, the default datapath ID is taken from the
+Ethernet address of the datapath's local port (which is typically
+randomly generated) in the lower 48 bits and zeros in the upper 16.
+
+.TP
+\fB--mgmt-id=\fImgmtid\fR
+Sets \fImgmtid\fR, which must consist of exactly 12 hexadecimal
+digits, as the switch's management ID.
+
+If this option is omitted, the management ID defaults to 0, signaling
+to the controller that management is supported but not configured.
+
+.TP
+\fB--mfr-desc=\fIdesc\fR
+Set the description of the switch's manufacturer to \fIdesc\fR, which
+may contain up to 255 ASCII characters.
+
+.TP
+\fB--hw-desc=\fIdesc\fR
+Set the description of the switch's hardware revision to \fIdesc\fR, which
+may contain up to 255 ASCII characters.
+
+.TP
+\fB--sw-desc=\fIdesc\fR
+Set the description of the switch's software revision to \fIdesc\fR, which
+may contain up to 255 ASCII characters.
+
+.TP
+\fB--serial-desc=\fIdesc\fR
+Set the description of the switch's serial number to \fIdesc\fR, which
+may contain up to 31 ASCII characters.
+
+.TP
+\fB--dp-desc=\fIdesc\fR
+Set the description of the datapath to \fIdesc\fR, which may contain up to
+255 ASCII characters.  Note that this field is intended for debugging
+purposes and is not guaranteed to be unique and should not be used as
+the primary identifier of the datapath.
+
+
 .SS "Controller Discovery Options"
 .TP
 \fB--accept-vconn=\fIregex\fR
@@ -196,13 +243,13 @@ When controller discovery is not performed, this option has no effect.
 .SS "Networking Options"
 .TP
 \fB--datapath-id=\fIdpid\fR
-Sets \fIdpid\fR, which must consist of exactly 12 hexadecimal digits,
+Sets \fIdpid\fR, which must consist of exactly 16 hexadecimal digits,
 as the datapath ID that the switch will use to identify itself to the
 OpenFlow controller.
 
 If this option is omitted, the default datapath ID is taken from the
 Ethernet address of the datapath's local port (which is typically
-randomly generated).
+randomly generated) in the lower 48 bits and zeros in the upper 16.
 
 .TP
 \fB--fail=\fR[\fBopen\fR|\fBclosed\fR]