are supported:
.RS
-.TP
-\fBssl:\fIhost\fR[\fB:\fIport\fR]
-The specified SSL \fIport\fR (default: 6633) on the given remote
-\fIhost\fR. The \fB--private-key\fR, \fB--certificate\fR, and
-\fB--ca-cert\fR options are mandatory when this form is used.
-
-.TP
-\fBtcp:\fIhost\fR[\fB:\fIport\fR]
-The specified TCP \fIport\fR (default: 6633) on the given remote
-\fIhost\fR.
-
-.TP
-\fBunix:\fIfile\fR
-The Unix domain server socket named \fIfile\fR.
-
+.so lib/vconn-active.man
+.
.IP "\fIfile\fR"
This is short for \fBunix:\fIfile\fR, as long as \fIfile\fR does not
contain a colon.
-
+.
.IP \fIdp\fR
This is short for \fBunix:@RUNDIR@/\fIdp\fB.mgmt\fR, as long as
\fIdp\fR does not contain a colon.
This command may be useful for debugging switch or controller
implementations.
-.TP
-\fBexecute \fIswitch command \fR[\fIarg\fR...]
-Sends a request to \fIswitch\fR to execute \fIcommand\fR along with
-each \fIarg\fR, if any, then waits for the command to complete and
-reports its completion status on \fBstderr\fR and its output, if any,
-on \fBstdout\fR. The set of available commands and their argument is
-switch-dependent. (This command uses a Nicira extension to OpenFlow
-that may not be available on all switches.)
-
.SS "OpenFlow Switch and Controller Commands"
The following commands, like those in the previous section, may be
.IP \fBmod_dl_dst\fB:\fImac\fR
Sets the destination Ethernet address to \fImac\fR.
+
+.IP \fBmod_nw_src\fB:\fIip\fR
+Sets the IPv4 source address to \fIip\fR.
+
+.IP \fBmod_nw_dst\fB:\fIip\fR
+Sets the IPv4 destination address to \fIip\fR.
+
+.IP \fBmod_tp_src\fB:\fIport\fR
+Sets the TCP or UDP source port to \fIport\fR.
+
+.IP \fBmod_tp_dst\fB:\fIport\fR
+Sets the TCP or UDP destination port to \fIport\fR.
.RE
.IP
\fB--strict\fR
Uses strict matching when running flow modification commands.
-.TP
-\fB-t\fR, \fB--timeout=\fIsecs\fR
-Limits \fBovs\-ofctl\fR runtime to approximately \fIsecs\fR seconds. If
-the timeout expires, \fBovs\-ofctl\fR will exit with a \fBSIGALRM\fR
-signal.
-
-.TP
-\fB-p\fR, \fB--private-key=\fIprivkey.pem\fR
-Specifies a PEM file containing the private key used as the
-identity for SSL connections to a switch.
-
-.TP
-\fB-c\fR, \fB--certificate=\fIcert.pem\fR
-Specifies a PEM file containing a certificate, signed by the
-controller's certificate authority (CA), that certifies the
-private key to identify a trustworthy controller.
-
-.TP
-\fB-C\fR, \fB--ca-cert=\fIcacert.pem\fR
-Specifies a PEM file containing the CA certificate used to verify that
-a switch is trustworthy.
-
+.so lib/ssl.man
.so lib/vlog.man
.so lib/common.man