openflow: Fix frag config flag values

[openvswitch] / utilities / ovs-ofctl.8.in

diff --git a/utilities/ovs-ofctl.8.in b/utilities/ovs-ofctl.8.in
index 17b5a4006f3b9e5d5dd3540bbdb3979575b7bd45..0faed9c97181eaaa11ae888b9247dea1d8861194 100644 (file)
--- a/utilities/ovs-ofctl.8.in
+++ b/utilities/ovs-ofctl.8.in
@@ -1,4 +1,4 @@
-.TH ovs\-ofctl 8 "June 2009" "Open vSwitch" "Open vSwitch Manual"
+.TH ovs\-ofctl 8 "January 2010" "Open vSwitch" "Open vSwitch Manual"
 .ds PN ovs\-ofctl
 
 .SH NAME
@@ -60,9 +60,11 @@ Prints to the console statistics for each of the flow tables used by
 \fIswitch\fR.
 
 .TP
-\fBdump-ports \fIswitch\fR
-Prints to the console statistics for each of the network devices
-associated with \fIswitch\fR.
+\fBdump-ports \fIswitch\fR [\fInetdev\fR]
+Prints to the console statistics for network devices associated with 
+\fIswitch\fR.  If \fInetdev\fR is specified, only the statistics
+associated with that device will be printed.  \fInetdev\fR can be an
+OpenFlow assigned port number or device name, e.g. \fBeth0\fR.
 
 .TP
 \fBmod-port \fIswitch\fR \fInetdev\fR \fIaction\fR
@@ -136,7 +138,7 @@ switch's tables are removed.  See \fBFlow Syntax\fR, below, for the
 syntax of \fIflows\fR.
 
 .TP
-\fBmonitor \fIswitch\fR [\fImiss-len\fR [\fIsend-exp]]
+\fBmonitor \fIswitch\fR [\fImiss-len\fR]
 Connects to \fIswitch\fR and prints to the console all OpenFlow
 messages received.  Usually, \fIswitch\fR should specify a connection
 named on \fBovs\-openflowd\fR(8)'s \fB-l\fR or \fB--listen\fR command line
@@ -149,11 +151,6 @@ OpenFlow reference implementation does not send these messages to the
 \fBovs\-ofctl monitor\fR client connection unless a nonzero value is
 specified on this argument.
 
-If \fIsend-exp\fR is specified as \fB1\fR, \fBovs\-ofctl\fR will also
-request to be sent flow expiration messages.  If this argument is
-omitted, or \fB0\fR is specified, then \fRovs\-ofctl\fR will not request
-flow expirations.
-
 This command may be useful for debugging switch or controller
 implementations.
 
@@ -212,6 +209,11 @@ as \fIvlan\fR to match packets that are not tagged with a Virtual LAN;
 otherwise, specify a number between 0 and 4095, inclusive, as the
 12-bit VLAN ID to match.
 
+.IP \fBdl_vlan_pcp=\fIpriority\fR
+Matches IEEE 802.1q Priority Code Point (PCP) \fIpriority\fR, which is
+specified as a value between 0 and 7, inclusive.  A higher value
+indicates a higher frame priority level.
+
 .IP \fBdl_src=\fImac\fR
 Matches Ethernet source address \fImac\fR, which is specified as 6 pairs 
 of hexadecimal digits delimited by colons (e.g. \fB00:0A:E4:25:6B:B0\fR).
@@ -240,6 +242,11 @@ Matches IPv4 destination address \fIip\fR.
 Matches IP protocol type \fIproto\fR, which is specified as a decimal 
 number between 0 and 255, inclusive (e.g. 6 to match TCP packets).
 
+.IP \fBnw_tos=\fItos\fR
+Matches IP ToS/DSCP field \fItos\fR, which is specified as a decimal 
+number between 0 and 255, inclusive.  Note that the two lower reserved
+bits are ignored for matching purposes.
+
 .IP \fBtp_src=\fIport\fR
 Matches UDP or TCP source port \fIport\fR, which is specified as a decimal 
 number between 0 and 65535, inclusive (e.g. 80 to match packets originating 
@@ -348,6 +355,12 @@ Sets the TCP or UDP source port to \fIport\fR.
 
 .IP \fBmod_tp_dst\fB:\fIport\fR
 Sets the TCP or UDP destination port to \fIport\fR.
+
+.IP \fBmod_nw_tos\fB:\fItos\fR
+Sets the IP ToS/DSCP field to \fItos\fR.  Valid values are between 0 and
+255, inclusive.  Note that the two lower reserved bits are never
+modified.
+
 .RE
 
 .IP