<dt><code>01:80:c2:00:00:0<var>x</var></code></dt>
<dd>Other reserved protocols.</dd>
- <dt><code>00:00:5e:00:01:<var>x</var><var>x</var></code></dt>
- <dd> VRRP IPv4 virtual router MAC address. </dd>
+ <dt><code>00:e0:2b:00:00:00</code></dt>
+ <dd>Extreme Discovery Protocol (EDP).</dd>
- <dt><code>00:00:5e:00:02:<var>x</var><var>x</var></code></dt>
- <dd> VRRP IPv6 virtual router MAC address. </dd>
-
- <dt><code>00:00:0c:07:ac:<var>x</var><var>x</var></code></dt>
- <dd> HSRP Version 1. </dd>
-
- <dt><code>00:00:0c:9f:f<var>x</var>:<var>x</var><var>x</var></code>
- </dt>
- <dd> HSRP Version 2. </dd>
-
- <dt><code>00:07:b4:<var>x</var><var>x</var>:<var>x</var><var>x</var>:<var>x</var><var>x</var></code></dt>
- <dd> GLBP. </dd>
+ <dt>
+ <code>00:e0:2b:00:00:04</code> and <code>00:e0:2b:00:00:06</code>
+ </dt>
+ <dd>Ethernet Automatic Protection Switching (EAPS).</dd>
<dt><code>01:00:0c:cc:cc:cc</code></dt>
<dd>
<dt><code>01:00:0c:00:00:00</code></dt>
<dd>Cisco Inter Switch Link.</dd>
+
+ <dt><code>01:00:0c:cc:cc:c<var>x</var></code></dt>
+ <dd>Cisco CFM.</dd>
</dl>
</column>
frame having an invalid interval.
</column>
- <column name="cfm_fault_status" key="sequence">
- Indicates a CFM fault was triggered because the CFM module received
- a CCM frame with a sequence number that it was not expecting.
- </column>
-
<column name="cfm_health">
<p>
Indicates the health of the interface as a percentage of CCM frames
<p>
The eviction process only considers flows that have an idle timeout or
a hard timeout. That is, eviction never deletes permanent flows.
- (Permanent flows do count against <ref column="flow_limit"/>.
+ (Permanent flows do count against <ref column="flow_limit"/>.)
</p>
<p>
Service (QoS) on IP networks.
The DSCP value specified here is used when establishing the connection
- between the controller and the Open vSwitch. The connection must be
- reset for the new DSCP values to take effect. If no value is
- specified, a default value of 48 is chosen. Valid DSCP values must be
- in the range 0 to 63.
+ between the controller and the Open vSwitch. If no value is specified,
+ a default value of 48 is chosen. Valid DSCP values must be in the
+ range 0 to 63.
</column>
</group>
Service (QoS) on IP networks.
The DSCP value specified here is used when establishing the connection
- between the manager and the Open vSwitch. The connection must be
- reset for the new DSCP values to take effect. If no value is
- specified, a default value of 48 is chosen. Valid DSCP values must be
- in the range 0 to 63.
+ between the manager and the Open vSwitch. If no value is specified, a
+ default value of 48 is chosen. Valid DSCP values must be in the range
+ 0 to 63.
</column>
</group>