included, then its MAC address is by default the lowest-numbered MAC
address among the other bridge ports, ignoring other internal ports
and bridge ports that are
-used as port mirroring destinations (see \fBPort Mirroring\fR, below). To
-use a specific MAC address instead, set \fBbridge.\fIname\fB.mac\fR to
-a MAC address in the format
+used as port mirroring destinations (see \fBPort Mirroring\fR, below).
+For this purpose, the MAC of a bonded port (see \fBNetwork Device
+Bonding\fR, below) is by default the MAC of its slave whose name is first in
+alphabetical order.
+There are two ways to modify this algorithm for selecting the MAC
+address of the local port:
+.IP \(bu
+To use a specific MAC address for the local port, set
+\fBbridge.\fIname\fB.mac\fR to a MAC address in the format
\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR, where each
-\fIx\fR is a hex digit. If no valid MAC address can be determined
+\fIx\fR is a hex digit.
+.IP \(bu
+To override the MAC of a port for the purpose of this algorithm, set
+\fBport.\fIport\fB.mac\fR to a MAC address in the format described
+above.
+.PP
+If no valid MAC address can be determined
either of these ways, then a MAC address is randomly generated.
.PP
The following syntax defines a bridge named \fBmybr\fR, configured
any existing tag; when it is sent out an implicit VLAN port, the frame
will not be tagged. This type of mirroring may be referred to as
RSPAN.
+.IP
+Please note that mirroring to a VLAN can disrupt a network that
+contains unmanaged switches. Consider an unmanaged physical switch
+with two ports: port 1, connected to an end host, and port 2,
+connected to an Open vSwitch configured to mirror received packets
+into VLAN 123 on port 2. Suppose that the end host sends a packet on
+port 1 that the physical switch forwards to port 2. The Open vSwitch
+forwards this packet to its destination and then reflects it back on
+port 2 in VLAN 123. This reflected packet causes the unmanaged
+physical switch to replace the MAC learning table entry, which
+correctly pointed to port 1, with one that incorrectly points to port
+2. Afterward, the physical switch will direct packets destined for
+the end host to the Open vSwitch on port 2, instead of to the end host
+on port 1, disrupting connectivity. If mirroring to a VLAN is desired
+in this scenario, then the physical switch must be replaced by one
+that learns Ethernet addresses on a per-VLAN basis.
.ST "Example"
The following \fBovs\-vswitchd\fR configuration copies all frames received
on \fBeth1\fR or \fBeth2\fR to \fBeth3\fR.
.PP
The maximum time between attempts to connect to the controller may be
specified in integral seconds with the \fBmgmt.max-backoff\fR key. The
-default maximum backoff is 15 seconds, and the minimum value is 1
+default maximum backoff is 8 seconds, and the minimum value is 1
second.
An inactivity probe may be configured with the \fBmgmt.inactivity-probe\fR
specified number of seconds, it will send a probe. If a response is not
received for an additional amount of that time, \fBovs\-vswitchd\fR assumes
the connection has been broken and attempts to reconnect. The default
-is 15 seconds, and the minimum value is 5 seconds.
+and minimum values are both 5 seconds.
A management id may be specified with the \fBmgmt.id\fR key. It takes
an id in the form of exactly 12 hexadecimal digits. If one is not
can pass through the switch at all.
.IP
The first of these that is set takes effect.
-If the value is \fBstandalone\fR, \fBovs\-vswitchd\fR will take over
+If the value is \fBstandalone\fR, or if neither of these settings
+is set, \fBovs\-vswitchd\fR will take over
responsibility for setting up
flows when no message has been received from the controller for three
times the inactivity probe interval (see above). In this mode,
to the controller in the background and, when the connection succeeds,
it discontinues its standalone behavior.
.IP
-If this option is set to \fBsecure\fR, or if neither of these settings
-is set, \fBovs\-vswitchd\fR will not set up flows on its own when the
-controller connection fails.
+If this option is set to \fBsecure\fR, \fBovs\-vswitchd\fR will not
+set up flows on its own when the controller connection fails.
.IP "\fBbridge.\fIname\fB.controller.max-backoff=\fIsecs\fR"
Sets the maximum time between attempts to connect to the controller to
\fIsecs\fR, which must be at least 1. The actual interval between