.\" -*- nroff -*- .de IQ . br . ns . IP "\\$1" .. .TH ovs\-ofctl 8 "January 2011" "Open vSwitch" "Open vSwitch Manual" .ds PN ovs\-ofctl . .SH NAME ovs\-ofctl \- administer OpenFlow switches . .SH SYNOPSIS .B ovs\-ofctl [\fIoptions\fR] \fIcommand \fR[\fIswitch\fR] [\fIargs\fR\&...] . .SH DESCRIPTION The .B ovs\-ofctl program is a command line tool for monitoring and administering OpenFlow switches. It can also show the current state of an OpenFlow switch, including features, configuration, and table entries. . .SS "OpenFlow Switch Management Commands" .PP These commands allow \fBovs\-ofctl\fR to monitor and administer an OpenFlow switch. It is able to show the current state of a switch, including features, configuration, and table entries. .PP Most of these commands take an argument that specifies the method for connecting to an OpenFlow switch. The following connection methods are supported: . .RS .so lib/vconn-active.man . .IP "\fIfile\fR" This is short for \fBunix:\fIfile\fR, as long as \fIfile\fR does not contain a colon. . .IP \fIbridge\fR This is short for \fBunix:@RUNDIR@/\fIbridge\fB.mgmt\fR, as long as \fIbridge\fR does not contain a colon. . .IP [\fItype\fB@\fR]\fIdp\fR Attempts to look up the bridge associated with \fIdp\fR and open as above. If \fItype\fR is given, it specifies the datapath provider of \fIdp\fR, otherwise the default provider \fBsystem\fR is assumed. .RE . .TP \fBshow \fIswitch\fR Prints to the console information on \fIswitch\fR, including information on its flow tables and ports. . .TP \fBdump\-tables \fIswitch\fR Prints to the console statistics for each of the flow tables used by \fIswitch\fR. . .TP \fBdump\-ports \fIswitch\fR [\fInetdev\fR] Prints to the console statistics for network devices associated with \fIswitch\fR. If \fInetdev\fR is specified, only the statistics associated with that device will be printed. \fInetdev\fR can be an OpenFlow assigned port number or device name, e.g. \fBeth0\fR. . .TP \fBmod\-port \fIswitch\fR \fInetdev\fR \fIaction\fR Modify characteristics of an interface monitored by \fIswitch\fR. \fInetdev\fR can be referred to by its OpenFlow assigned port number or the device name, e.g. \fBeth0\fR. The \fIaction\fR may be any one of the following: . .RS .IP \fBup\fR Enables the interface. This is equivalent to ``ifconfig up'' on a Unix system. . .IP \fBdown\fR Disables the interface. This is equivalent to ``ifconfig down'' on a Unix system. . .IP \fBflood\fR When a \fIflood\fR action is specified, traffic will be sent out this interface. This is the default posture for monitored ports. . .IP \fBnoflood\fR When a \fIflood\fR action is specified, traffic will not be sent out this interface. This is primarily useful to prevent loops when a spanning tree protocol is not in use. . .RE . .TP \fBdump\-flows \fIswitch \fR[\fIflows\fR] Prints to the console all flow entries in \fIswitch\fR's tables that match \fIflows\fR. If \fIflows\fR is omitted, all flows in the switch are retrieved. See \fBFlow Syntax\fR, below, for the syntax of \fIflows\fR. The output format is described in \fBTable Entry Output\fR. . .TP \fBdump\-aggregate \fIswitch \fR[\fIflows\fR] Prints to the console aggregate statistics for flows in \fIswitch\fR's tables that match \fIflows\fR. If \fIflows\fR is omitted, the statistics are aggregated across all flows in the switch's flow tables. See \fBFlow Syntax\fR, below, for the syntax of \fIflows\fR. The output format is descrbed in \fBTable Entry Output\fR. . .IP "\fBqueue\-stats \fIswitch \fR[\fIport \fR[\fIqueue\fR]]" Prints to the console statistics for the specified \fIqueue\fR on \fIport\fR within \fIswitch\fR. Either of \fIport\fR or \fIqueue\fR or both may be omitted (or equivalently specified as \fBALL\fR). If both are omitted, statistics are printed for all queues on all ports. If only \fIqueue\fR is omitted, then statistics are printed for all queues on \fIport\fR; if only \fIport\fR is omitted, then statistics are printed for \fIqueue\fR on every port where it exists. . .SS "OpenFlow Switch Flow Table Commands" . These commands manage the flow table in an OpenFlow switch. In each case, \fIflow\fR specifies a flow entry in the format described in \fBFlow Syntax\fR, below, and \fIfile\fR is a text file that contains zero or more flows in the same syntax, one per line. . .IP "\fBadd\-flow \fIswitch flow\fR" .IQ "\fBadd\-flow \fIswitch \fB\- < \fIfile\fR" .IQ "\fBadd\-flows \fIswitch file\fR" Add each flow entry to \fIswitch\fR's tables. . .IP "[\fB\-\-strict\fR] \fBmod\-flows \fIswitch flow\fR" .IQ "[\fB\-\-strict\fR] \fBmod\-flows \fIswitch \fB\- < \fIfile\fR" Modify the actions in entries from \fIswitch\fR's tables that match the specified flows. With \fB\-\-strict\fR, wildcards are not treated as active for matching purposes. . .IP "\fBdel\-flows \fIswitch\fR" .IQ "[\fB\-\-strict\fR] \fBdel\-flows \fIswitch \fR[\fIflow\fR]" .IQ "[\fB\-\-strict\fR] \fBdel\-flows \fIswitch \fB\- < \fIfile\fR" Deletes entries from \fIswitch\fR's flow table. With only a \fIswitch\fR argument, deletes all flows. Otherwise, deletes flow entries that match the specified flows. With \fB\-\-strict\fR, wildcards are not treated as active for matching purposes. . .IP "\fBreplace\-flows \fIswitch file\fR" Reads flow entries from \fIfile\fR (or \fBstdin\fR if \fIfile\fR is \fB\-\fR) and queries the flow table from \fIswitch\fR. Then it fixes up any differences, adding flows from \fIflow\fR that are missing on \fIswitch\fR, deleting flows from \fIswitch\fR that are not in \fIfile\fR, and updating flows in \fIswitch\fR whose actions, cookie, or timeouts differ in \fIfile\fR. . .IP "\fBdiff\-flows \fIsource1 source2\fR" Reads flow entries from \fIsource1\fR and \fIsource2\fR and prints the differences. A flow that is in \fIsource1\fR but not in \fIsource2\fR is printed preceded by a \fB\-\fR, and a flow that is in \fIsource2\fR but not in \fIsource1\fR is printed preceded by a \fB+\fR. If a flow exists in both \fIsource1\fR and \fIsource2\fR with different actions, cookie, or timeouts, then both versions are printed preceded by \fB\-\fR and \fB+\fR, respectively. .IP \fIsource1\fR and \fIsource2\fR may each name a file or a switch. If a name begins with \fB/\fR or \fB.\fR, then it is considered to be a file name. A name that contains \fB:\fR is considered to be a switch. Otherwise, it is a file if a file by that name exists, a switch if not. .IP For this command, an exit status of 0 means that no differences were found, 1 means that an error occurred, and 2 means that some differences were found. . .SS "OpenFlow Switch Monitoring Commands" . .IP "\fBsnoop \fIswitch\fR" Connects to \fIswitch\fR and prints to the console all OpenFlow messages received. Unlike other \fBovs\-ofctl\fR commands, if \fIswitch\fR is the name of a bridge, then the \fBsnoop\fR command connects to a Unix domain socket named \fB@RUNDIR@/\fIbridge\fB.snoop\fR. \fBovs\-vswitchd\fR listens on such a socket for each bridge and sends to it all of the OpenFlow messages sent to or received from its configured OpenFlow controller. Thus, this command can be used to view OpenFlow protocol activity between a switch and its controller. .IP When a switch has more than one controller configured, only the traffic to and from a single controller is output. If none of the controllers is configured as a master or a slave (using a Nicira extension to OpenFlow), then a controller is chosen arbitrarily among them. If there is a master controller, it is chosen; otherwise, if there are any controllers that are not masters or slaves, one is chosen arbitrarily; otherwise, a slave controller is chosen arbitrarily. This choice is made once at connection time and does not change as controllers reconfigure their roles. .IP If a switch has no controller configured, or if the configured controller is disconnected, no traffic is sent, so monitoring will not show any traffic. . .IP "\fBmonitor \fIswitch\fR [\fImiss-len\fR]" Connects to \fIswitch\fR and prints to the console all OpenFlow messages received. Usually, \fIswitch\fR should specify the name of a bridge in the \fBovs\-vswitchd\fR database. .IP If \fImiss-len\fR is provided, \fBovs\-ofctl\fR sends an OpenFlow ``set configuration'' message at connection setup time that requests \fImiss-len\fR bytes of each packet that misses the flow table. Open vSwitch does not send these and other asynchronous messages to an \fBovs\-ofctl monitor\fR client connection unless a nonzero value is specified on this argument. (Thus, if \fImiss\-len\fR is not specified, very little traffic will ordinarily be printed.) .IP This command may be useful for debugging switch or controller implementations. . .SS "OpenFlow Switch and Controller Commands" . The following commands, like those in the previous section, may be applied to OpenFlow switches, using any of the connection methods described in that section. Unlike those commands, these may also be applied to OpenFlow controllers. . .TP \fBprobe \fItarget\fR Sends a single OpenFlow echo-request message to \fItarget\fR and waits for the response. With the \fB\-t\fR or \fB\-\-timeout\fR option, this command can test whether an OpenFlow switch or controller is up and running. . .TP \fBping \fItarget \fR[\fIn\fR] Sends a series of 10 echo request packets to \fItarget\fR and times each reply. The echo request packets consist of an OpenFlow header plus \fIn\fR bytes (default: 64) of randomly generated payload. This measures the latency of individual requests. . .TP \fBbenchmark \fItarget n count\fR Sends \fIcount\fR echo request packets that each consist of an OpenFlow header plus \fIn\fR bytes of payload and waits for each response. Reports the total time required. This is a measure of the maximum bandwidth to \fItarget\fR for round-trips of \fIn\fR-byte messages. . .SS "Flow Syntax" .PP Some \fBovs\-ofctl\fR commands accept an argument that describes a flow or flows. Such flow descriptions comprise a series \fIfield\fB=\fIvalue\fR assignments, separated by commas or white space. (Embedding spaces into a flow description normally requires quoting to prevent the shell from breaking the description into multiple arguments.) .PP Flow descriptions should be in \fBnormal form\fR. This means that a flow may only specify a value for an L3 field if it also specifies a particular L2 protocol, and that a flow may only specify an L4 field if it also specifies particular L2 and L3 protocol types. For example, if the L2 protocol type \fBdl_type\fR is wildcarded, then L3 fields \fBnw_src\fR, \fBnw_dst\fR, and \fBnw_proto\fR must also be wildcarded. Similarly, if \fBdl_type\fR or \fBnw_proto\fR (the L3 protocol type) is wildcarded, so must be \fBtp_dst\fR and \fBtp_src\fR, which are L4 fields. \fBovs\-ofctl\fR will warn about flows not in normal form. .PP The following field assignments describe how a flow matches a packet. If any of these assignments is omitted from the flow syntax, the field is treated as a wildcard; thus, if all of them are omitted, the resulting flow matches all packets. The string \fB*\fR or \fBANY\fR may be specified to explicitly mark any of these fields as a wildcard. (\fB*\fR should be quoted to protect it from shell expansion.) . .IP \fBin_port=\fIport_no\fR Matches physical port \fIport_no\fR. Switch ports are numbered as displayed by \fBovs\-ofctl show\fR. . .IP \fBdl_vlan=\fIvlan\fR Matches IEEE 802.1q Virtual LAN tag \fIvlan\fR. Specify \fB0xffff\fR as \fIvlan\fR to match packets that are not tagged with a Virtual LAN; otherwise, specify a number between 0 and 4095, inclusive, as the 12-bit VLAN ID to match. . .IP \fBdl_vlan_pcp=\fIpriority\fR Matches IEEE 802.1q Priority Code Point (PCP) \fIpriority\fR, which is specified as a value between 0 and 7, inclusive. A higher value indicates a higher frame priority level. . .IP \fBdl_src=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR .IQ \fBdl_dst=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR Matches an Ethernet source (or destination) address specified as 6 pairs of hexadecimal digits delimited by colons (e.g. \fB00:0A:E4:25:6B:B0\fR). . .IP \fBdl_dst=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB/\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR Matches an Ethernet destination address specified as 6 pairs of hexadecimal digits delimited by colons (e.g. \fB00:0A:E4:25:6B:B0\fR), with a wildcard mask following the slash. Only the following masks are allowed: .RS .IP \fB01:00:00:00:00:00\fR Match only the multicast bit. Thus, \fBdl_dst=01:00:00:00:00:00/01:00:00:00:00:00\fR matches all multicast (including broadcast) Ethernet packets, and \fBdl_dst=00:00:00:00:00:00/01:00:00:00:00:00\fR matches all unicast Ethernet packets. .IP \fBfe:ff:ff:ff:ff:ff\fR Match all bits except the multicast bit. This is probably not useful. .IP \fBff:ff:ff:ff:ff:ff\fR Exact match (equivalent to omitting the mask). .IP \fB00:00:00:00:00:00\fR Wildcard all bits (equivalent to \fBdl_dst=*\fR.) .RE . .IP \fBdl_type=\fIethertype\fR Matches Ethernet protocol type \fIethertype\fR, which is specified as an integer between 0 and 65535, inclusive, either in decimal or as a hexadecimal number prefixed by \fB0x\fR (e.g. \fB0x0806\fR to match ARP packets). . .IP \fBnw_src=\fIip\fR[\fB/\fInetmask\fR] .IQ \fBnw_dst=\fIip\fR[\fB/\fInetmask\fR] When \fBdl_type\fR is 0x0800 (possibly via shorthand, e.g. \fBip\fR or \fBtcp\fR), matches IPv4 source (or destination) address \fIip\fR, which may be specified as an IP address or host name (e.g. \fB192.168.1.1\fR or \fBwww.example.com\fR). The optional \fInetmask\fR allows restricting a match to an IPv4 address prefix. The netmask may be specified as a dotted quad (e.g. \fB192.168.1.0/255.255.255.0\fR) or as a CIDR block (e.g. \fB192.168.1.0/24\fR). .IP When \fBdl_type=0x0806\fR or \fBarp\fR is specified, matches the \fBar_spa\fR or \fBar_tpa\fR field, respectively, in ARP packets for IPv4 and Ethernet. .IP When \fBdl_type\fR is wildcarded or set to a value other than 0x0800 or 0x0806, the values of \fBnw_src\fR and \fBnw_dst\fR are ignored (see \fBFlow Syntax\fR above). . .IP \fBnw_proto=\fIproto\fR When \fBip\fR or \fBdl_type=0x0800\fR is specified, matches IP protocol type \fIproto\fR, which is specified as a decimal number between 0 and 255, inclusive (e.g. 1 to match ICMP packets or 6 to match TCP packets). .IP When \fBipv6\fR or \fBdl_type=0x86dd\fR is specified, matches IPv6 header type \fIproto\fR, which is specified as a decimal number between 0 and 255, inclusive (e.g. 58 to match ICMPv6 packets or 6 to match TCP). The header type is the terminal header as described in the \fBDESIGN\fR document. .IP When \fBarp\fR or \fBdl_type=0x0806\fR is specified, matches the lower 8 bits of the ARP opcode. ARP opcodes greater than 255 are treated as 0. .IP When \fBdl_type\fR is wildcarded or set to a value other than 0x0800, 0x0806, or 0x86dd, the value of \fBnw_proto\fR is ignored (see \fBFlow Syntax\fR above). . .IP \fBnw_tos=\fItos\fR Matches IP ToS/DSCP or IPv6 traffic class field \fItos\fR, which is specified as a decimal number between 0 and 255, inclusive. Note that the two lower reserved bits are ignored for matching purposes. .IP When \fBdl_type\fR is wildcarded or set to a value other than 0x0800, 0x0806, or 0x86dd, the value of \fBnw_tos\fR is ignored (see \fBFlow Syntax\fR above). . .IP \fBtp_src=\fIport\fR .IQ \fBtp_dst=\fIport\fR When \fBdl_type\fR and \fBnw_proto\fR specify TCP or UDP, \fBtp_src\fR and \fBtp_dst\fR match the UDP or TCP source or destination port \fIport\fR, respectively. which is specified as a decimal number between 0 and 65535, inclusive (e.g. 80 to match packets originating from a HTTP server). .IP When \fBdl_type\fR and \fBnw_proto\fR take other values, the values of these settings are ignored (see \fBFlow Syntax\fR above). . .IP \fBicmp_type=\fItype\fR .IQ \fBicmp_code=\fIcode\fR When \fBdl_type\fR and \fBnw_proto\fR specify ICMP or ICMPv6, \fItype\fR matches the ICMP type and \fIcode\fR matches the ICMP code. Each is specified as a decimal number between 0 and 255, inclusive. .IP When \fBdl_type\fR and \fBnw_proto\fR take other values, the values of these settings are ignored (see \fBFlow Syntax\fR above). . .IP \fBtable=\fInumber\fR If specified, limits the flow manipulation and flow dump commands to only apply to the table with the given \fInumber\fR. \fInumber\fR is a number between 0 and 254, inclusive. . Behavior varies if \fBtable\fR is not specified. For flow table modification commands without \fB\-\-strict\fR, the switch will choose the table for these commands to operate on. For flow table modification commands with \fB\-\-strict\fR, the command will operate on any single matching flow in any table; it will do nothing if there are matches in more than one table. The \fBdump-flows\fR and \fBdump-aggregate\fR commands will gather statistics about flows from all tables. .IP When this field is specified in \fBadd-flow\fR, \fBadd-flows\fR, \fBmod-flows\fR and \fBdel-flows\fR commands, it activates a Nicira extension to OpenFlow, which as of this writing is only known to be implemented by Open vSwitch. . .PP The following shorthand notations are also available: . .IP \fBip\fR Same as \fBdl_type=0x0800\fR. . .IP \fBicmp\fR Same as \fBdl_type=0x0800,nw_proto=1\fR. . .IP \fBtcp\fR Same as \fBdl_type=0x0800,nw_proto=6\fR. . .IP \fBudp\fR Same as \fBdl_type=0x0800,nw_proto=17\fR. . .IP \fBarp\fR Same as \fBdl_type=0x0806\fR. . .PP The following field assignments require support for the NXM (Nicira Extended Match) extension to OpenFlow. When one of these is specified, \fBovs\-ofctl\fR will automatically attempt to negotiate use of this extension. If the switch does not support NXM, then \fBovs\-ofctl\fR will report a fatal error. . .IP \fBarp_sha=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR .IQ \fBarp_tha=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR When \fBdl_type\fR specifies ARP, \fBarp_sha\fR and \fBarp_tha\fR match the source and target hardware address, respectively. An address is specified as 6 pairs of hexadecimal digits delimited by colons. . .IP \fBipv6_src=\fIipv6\fR[\fB/\fInetmask\fR] .IQ \fBipv6_dst=\fIipv6\fR[\fB/\fInetmask\fR] When \fBdl_type\fR is 0x86dd (possibly via shorthand, e.g., \fBipv6\fR or \fBtcp6\fR), matches IPv6 source (or destination) address \fIipv6\fR, which may be specified as defined in RFC 2373. The preferred format is \fIx\fB:\fIx\fB:\fIx\fB:\fIx\fB:\fIx\fB:\fIx\fB:\fIx\fB:\fIx\fR, where \fIx\fR are the hexadecimal values of the eight 16-bit pieces of the address. A single instance of \fB::\fR may be used to indicate multiple groups of 16-bits of zeros. The optional \fInetmask\fR allows restricting a match to an IPv6 address prefix. A netmask is specified as a CIDR block (e.g. \fB2001:db8:3c4d:1::/64\fR). . .IP \fBnd_target=\fIipv6\fR When \fBdl_type\fR, \fBnw_proto\fR, and \fBicmp_type\fR specify IPv6 Neighbor Discovery (ICMPv6 type 135 or 136), matches the target address \fIipv6\fR. \fIipv6\fR is in the same format described earlier for the \fBipv6_src\fR and \fBipv6_dst\fR fields. . .IP \fBnd_sll=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR When \fBdl_type\fR, \fBnw_proto\fR, and \fBicmp_type\fR specify IPv6 Neighbor Solicitation (ICMPv6 type 135), matches the source link\-layer address option. An address is specified as 6 pairs of hexadecimal digits delimited by colons. . .IP \fBnd_tll=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR When \fBdl_type\fR, \fBnw_proto\fR, and \fBicmp_type\fR specify IPv6 Neighbor Advertisement (ICMPv6 type 136), matches the target link\-layer address option. An address is specified as 6 pairs of hexadecimal digits delimited by colons. . .IP \fBtun_id=\fItunnel-id\fR[\fB/\fImask\fR] Matches tunnel identifier \fItunnel-id\fR. Only packets that arrive over a tunnel that carries a key (e.g. GRE with the RFC 2890 key extension) will have a nonzero tunnel ID. If \fImask\fR is omitted, \fItunnel-id\fR is the exact tunnel ID to match; if \fImask\fR is specified, then a 1-bit in \fImask\fR indicates that the corresponding bit in \fItunnel-id\fR must match exactly, and a 0-bit wildcards that bit. .IP In an attempt to be compatible with more switches, \fBovs\-ofctl\fR will prefer to use the ``tunnel ID from cookie'' Nicira extension to NXM. The use of this extension comes with three caveats: the top 32 bits of the \fBcookie\fR (see below) are used for \fItunnel-id\fR and thus unavailable for other use, specifying \fBtun_id\fR on \fBdump\-flows\fR or \fBdump\-aggregate\fR has no effect, and \fImask\fR is not supported. If any of these caveats apply, \fBovs-ofctl\fR will use NXM. . .IP "\fBreg\fIidx\fB=\fIvalue\fR[\fB/\fImask\fR]" Matches \fIvalue\fR either exactly or with optional \fImask\fR in register number \fIidx\fR. The valid range of \fIidx\fR depends on the switch. \fIvalue\fR and \fImask\fR are 32-bit integers, by default in decimal (use a \fB0x\fR prefix to specify hexadecimal). Arbitrary \fImask\fR values are allowed: a 1-bit in \fImask\fR indicates that the corresponding bit in \fIvalue\fR must match exactly, and a 0-bit wildcards that bit. .IP When a packet enters an OpenFlow switch, all of the registers are set to 0. Only explicit Nicira extension actions change register values. . .PP Defining IPv6 flows (those with \fBdl_type\fR equal to 0x86dd) requires support for NXM. The following shorthand notations are available for IPv6-related flows: . .IP \fBipv6\fR Same as \fBdl_type=0x86dd\fR. . .IP \fBtcp6\fR Same as \fBdl_type=0x86dd,nw_proto=6\fR. . .IP \fBudp6\fR Same as \fBdl_type=0x86dd,nw_proto=17\fR. . .IP \fBicmp6\fR Same as \fBdl_type=0x86dd,nw_proto=58\fR. . .PP The \fBadd\-flow\fR and \fBadd\-flows\fR commands require an additional field, which must be the final field specified: . .IP \fBactions=\fR[\fItarget\fR][\fB,\fItarget\fR...]\fR Specifies a comma-separated list of actions to take on a packet when the flow entry matches. If no \fItarget\fR is specified, then packets matching the flow are dropped. The \fItarget\fR may be a decimal port number designating the physical port on which to output the packet, or one of the following keywords: . .RS .IP \fBoutput\fR:\fIport\fR Outputs the packet on the port specified by \fIport\fR. . .IP \fBenqueue\fR:\fIport\fB:\fIqueue\fR Enqueues the packet on the specified \fIqueue\fR within port \fIport\fR. The number of supported queues depends on the switch; some OpenFlow implementations do not support queuing at all. . .IP \fBnormal\fR Subjects the packet to the device's normal L2/L3 processing. (This action is not implemented by all OpenFlow switches.) . .IP \fBflood\fR Outputs the packet on all switch physical ports other than the port on which it was received and any ports on which flooding is disabled (typically, these would be ports disabled by the IEEE 802.1D spanning tree protocol). . .IP \fBall\fR Outputs the packet on all switch physical ports other than the port on which it was received. . .IP \fBcontroller\fR:\fImax_len\fR Sends the packet to the OpenFlow controller as a ``packet in'' message. If \fImax_len\fR is a number, then it specifies the maximum number of bytes that should be sent. If \fImax_len\fR is \fBALL\fR or omitted, then the entire packet is sent. . .IP \fBlocal\fR Outputs the packet on the ``local port,'' which corresponds to the network device that has the same name as the bridge. . .IP \fBdrop\fR Discards the packet, so no further processing or forwarding takes place. If a drop action is used, no other actions may be specified. . .IP \fBmod_vlan_vid\fR:\fIvlan_vid\fR Modifies the VLAN id on a packet. The VLAN tag is added or modified as necessary to match the value specified. If the VLAN tag is added, a priority of zero is used (see the \fBmod_vlan_pcp\fR action to set this). . .IP \fBmod_vlan_pcp\fR:\fIvlan_pcp\fR Modifies the VLAN priority on a packet. The VLAN tag is added or modified as necessary to match the value specified. Valid values are between 0 (lowest) and 7 (highest). If the VLAN tag is added, a vid of zero is used (see the \fBmod_vlan_vid\fR action to set this). . .IP \fBstrip_vlan\fR Strips the VLAN tag from a packet if it is present. . .IP \fBmod_dl_src\fB:\fImac\fR Sets the source Ethernet address to \fImac\fR. . .IP \fBmod_dl_dst\fB:\fImac\fR Sets the destination Ethernet address to \fImac\fR. . .IP \fBmod_nw_src\fB:\fIip\fR Sets the IPv4 source address to \fIip\fR. . .IP \fBmod_nw_dst\fB:\fIip\fR Sets the IPv4 destination address to \fIip\fR. . .IP \fBmod_tp_src\fB:\fIport\fR Sets the TCP or UDP source port to \fIport\fR. . .IP \fBmod_tp_dst\fB:\fIport\fR Sets the TCP or UDP destination port to \fIport\fR. . .IP \fBmod_nw_tos\fB:\fItos\fR Sets the IP ToS/DSCP field to \fItos\fR. Valid values are between 0 and 255, inclusive. Note that the two lower reserved bits are never modified. . .RE .IP The following actions are Nicira vendor extensions that, as of this writing, are only known to be implemented by Open vSwitch: . .RS . .IP \fBresubmit\fB:\fIport\fR Re-searches the OpenFlow flow table with the \fBin_port\fR field replaced by \fIport\fR and executes the actions found, if any, in addition to any other actions in this flow entry. Recursive \fBresubmit\fR actions are ignored. . .IP \fBset_tunnel\fB:\fIid\fR .IQ \fBset_tunnel64\fB:\fIid\fR If outputting to a port that encapsulates the packet in a tunnel and supports an identifier (such as GRE), sets the identifier to \fBid\fR. If the \fBset_tunnel\fR form is used and \fIid\fR fits in 32 bits, then this uses an action extension that is supported by Open vSwitch 1.0 and later. Otherwise, if \fIid\fR is a 64-bit value, it requires Open vSwitch 1.1 or later. . .IP \fBdrop_spoofed_arp\fR Stops processing further actions, if the packet being processed is an Ethernet+IPv4 ARP packet for which the source Ethernet address inside the ARP packet differs from the source Ethernet address in the Ethernet header. .IP This action is deprecated in favor of defining flows using the \fBarp_sha\fR match field described earlier and will likely be removed in a future version of Open vSwitch. . .IP \fBset_queue\fB:\fIqueue\fR Sets the queue that should be used to \fIqueue\fR when packets are output. The number of supported queues depends on the switch; some OpenFlow implementations do not support queuing at all. . .IP \fBpop_queue\fR Restores the queue to the value it was before any \fBset_queue\fR actions were applied. . .IP \fBnote:\fR[\fIhh\fR]... Does nothing at all. Any number of bytes represented as hex digits \fIhh\fR may be included. Pairs of hex digits may be separated by periods for readability. . .IP "\fBmove:\fIsrc\fB[\fIstart\fB..\fIend\fB]->\fIdst\fB[\fIstart\fB..\fIend\fB]\fR" Copies the named bits from field \fIsrc\fR to field \fIdst\fR. \fIsrc\fR and \fIdst\fR must be NXM field names as defined in \fBnicira\-ext.h\fR, e.g. \fBNXM_OF_UDP_SRC\fR or \fBNXM_NX_REG0\fR. Each \fIstart\fR and \fIend\fR pair, which are inclusive, must specify the same number of bits and must fit within its respective field. Shorthands for \fB[\fIstart\fB..\fIend\fB]\fR exist: use \fB[\fIbit\fB]\fR to specify a single bit or \fB[]\fR to specify an entire field. .IP Examples: \fBmove:NXM_NX_REG0[0..5]\->NXM_NX_REG1[26..31]\fR copies the six bits numbered 0 through 5, inclusive, in register 0 into bits 26 through 31, inclusive; \fBmove:NXM_NX_REG0[0..15]->NXM_OF_VLAN_TCI[]\fR copies the least significant 16 bits of register 0 into the VLAN TCI field. . .IP "\fBload:\fIvalue\fB\->\fIdst\fB[\fIstart\fB..\fIend\fB]" Writes \fIvalue\fR to bits \fIstart\fR through \fIend\fR, inclusive, in field \fBdst\fR. .IP Example: \fBload:55\->NXM_NX_REG2[0..5]\fR loads value 55 (bit pattern \fB110111\fR) into bits 0 through 5, inclusive, in register 2. . .IP "\fBmultipath(\fIfields\fB, \fIbasis\fB, \fIalgorithm\fB, \fIn_links\fB, \fIarg\fB, \fIdst\fB[\fIstart\fB..\fIend\fB])\fR" Hashes \fIfields\fR using \fIbasis\fR as a universal hash parameter, then the applies multipath link selection \fIalgorithm\fR (with parameter \fIarg\fR) to choose one of \fIn_links\fR output links numbered 0 through \fIn_links\fR minus 1, and stores the link into \fIdst\fB[\fIstart\fB..\fIend\fB]\fR, which must be an NXM register as described above. .IP Currently, \fIfields\fR must be either \fBeth_src\fR or \fBsymmetric_l4\fR and \fIalgorithm\fR must be one of \fBmodulo_n\fR, \fBhash_threshold\fR, \fBhrw\fR, and \fBiter_hash\fR. Only the \fBiter_hash\fR algorithm uses \fIarg\fR. .IP Refer to \fBnicira\-ext.h\fR for more details. . .IP "\fBautopath(\fIid\fB, \fIdst\fB[\fIstart\fB..\fIend\fB])\fR" Given \fIid\fR, chooses an OpenFlow port and populates it in \fIdst\fB[\fIstart\fB..\fIend\fB]\fR, which must be an NXM register as described above. .IP Currently, \fIid\fR should be the OpenFlow port number of an interface on the bridge. If it isn't then \fIdst\fB[\fIstart\fB..\fIend\fB]\fR will be populated with the OpenFlow port "none". If \fIid\fR is a member of a bond, the normal bond selection logic will be used to choose the destination port. Otherwise, the register will be populated with \fIid\fR itself. .IP Refer to \fBnicira\-ext.h\fR for more details. .RE . .IP (The OpenFlow protocol supports other actions that \fBovs\-ofctl\fR does not yet expose to the user.) . .PP The \fBadd\-flow\fR, \fBadd\-flows\fR, and \fBmod\-flows\fR commands support an additional optional field: . .IP \fBcookie=\fIvalue\fR . A cookie is an opaque identifier that can be associated with the flow. \fIvalue\fR can be any 64-bit number and need not be unique among flows. . .PP The following additional field sets the priority for flows added by the \fBadd\-flow\fR and \fBadd\-flows\fR commands. For \fBmod\-flows\fR and \fBdel\-flows\fR when \fB\-\-strict\fR is specified, priority must match along with the rest of the flow specification. Other commands ignore the priority value. . .IP \fBpriority=\fIvalue\fR The priority at which a wildcarded entry will match in comparison to others. \fIvalue\fR is a number between 0 and 65535, inclusive. A higher \fIvalue\fR will match before a lower one. An exact-match entry will always have priority over an entry containing wildcards, so it has an implicit priority value of 65535. When adding a flow, if the field is not specified, the flow's priority will default to 32768. . .PP The \fBadd\-flow\fR and \fBadd\-flows\fR commands support additional optional fields: . .TP \fBidle_timeout=\fIseconds\fR Causes the flow to expire after the given number of seconds of inactivity. A value of 0 (the default) prevents a flow from expiring due to inactivity. . .IP \fBhard_timeout=\fIseconds\fR Causes the flow to expire after the given number of seconds, regardless of activity. A value of 0 (the default) gives the flow no hard expiration deadline. . .PP The \fBdump\-flows\fR, \fBdump\-aggregate\fR, \fBdel\-flow\fR and \fBdel\-flows\fR commands support one additional optional field: . .TP \fBout_port=\fIport\fR If set, a matching flow must include an output action to \fIport\fR. . .PP The \fBdump\-flows\fR and \fBdump\-aggregate\fR commands support an additional optional field: . .SS "Table Entry Output" . The \fBdump\-tables\fR and \fBdump\-aggregate\fR commands print information about the entries in a datapath's tables. Each line of output is a unique flow entry, which begins with some common information: . .IP \fBduration\fR The number of seconds the entry has been in the table. . .IP \fBtable_id\fR The table that contains the flow. When a packet arrives, the switch begins searching for an entry at the lowest numbered table. Tables are numbered as shown by the \fBdump\-tables\fR command. . .IP \fBpriority\fR The priority of the entry in relation to other entries within the same table. A higher value will match before a lower one. . .IP \fBn_packets\fR The number of packets that have matched the entry. . .IP \fBn_bytes\fR The total number of bytes from packets that have matched the entry. . .PP The rest of the line consists of a description of the flow entry as described in \fBFlow Syntax\fR, above. . . .SH OPTIONS .TP \fB\-\-strict\fR Uses strict matching when running flow modification commands. . .IP "\fB\-F \fIformat\fR" .IQ "\fB\-\-flow\-format=\fIformat\fR" \fBovs\-ofctl\fR supports the following flow formats, in order of increasing capability: .RS .IP "\fBopenflow10\fR" This is the standard OpenFlow 1.0 flow format. It should be supported by all OpenFlow switches. . .IP "\fBnxm\fR (Nicira Extended Match)" This Nicira extension to OpenFlow is flexible and extensible. It supports all of the Nicira flow extensions, such as \fBtun_id\fR and registers. .RE .IP Usually, \fBovs\-ofctl\fR picks the correct format automatically. For commands that modify the flow table, \fBovs\-ofctl\fR by default uses the most widely supported flow format that supports the flows being added. For commands that query the flow table, \fBovs\-ofctl\fR by default queries and uses the most advanced format supported by the switch. .IP This option, where \fIformat\fR is one of the formats listed in the above table, overrides \fBovs\-ofctl\fR's default choice of flow format. If a command cannot work as requested using the requested flow format, \fBovs\-ofctl\fR will report a fatal error. . .IP "\fB\-m\fR" .IQ "\fB\-\-more\fR" Increases the verbosity of OpenFlow messages printed and logged by \fBovs\-ofctl\fR commands. Specify this option more than once to increase verbosity further. .SS "Public Key Infrastructure Options" .so lib/ssl.man .so lib/vlog.man .so lib/common.man . .SH EXAMPLES . The following examples assume that \fBovs\-vswitchd\fR has a bridge named \fBbr0\fR configured. . .TP \fBovs\-ofctl dump\-tables br0\fR Prints out the switch's table stats. (This is more interesting after some traffic has passed through.) . .TP \fBovs\-ofctl dump\-flows br0\fR Prints the flow entries in the switch. . .SH "SEE ALSO" . .BR ovs\-appctl (8), .BR ovs\-controller (8), .BR ovs\-vswitchd (8)